Kair KHRV150/12RH Installation & Maintenance Instructions Manual Download

Page: 1 / 12

Kair Single Room
Heat Recovery Ventilator

INSTALLATION & MAINTENANCE INSTRUCTIONS

Contents

Page

Content

Safety First
Isolating Transformer (Humidity sensor unit).

Transformer/Humidity Sensor Unit
Siting the Ventilator

Installation
Outside installation of finisher ring

4 & 5

Inside installation of the finisher ring

6 & 7

Location of the Transformer/Humidity Sensor unit

Transformer/Humidity Sensor unit Wiring

Light Level Sensor

8, 9 & 10

Maintenance

Registration

Warranty

www.kair.co.uk

What am I?

Included items

Description

Qty

Through Wall unit

Transformer
& humidity sensor

Blanking Plate

(optional)

Wall Mounting Screws

Rawplug

Tamperproof Screws

(optional)

For unit and transformer
- require KTMPB to use

Installation and Maintenance
instructions

User Guide

Model:

KHRV150/12RH - Pullcord & Humidistat
KHRV150/12PC - Pullcord

Please read and save these instructions

Summary of Contents for KHRV150/12RH













Search results

Summary of Contents for KHRV150/12RH

Reviews:

Related manuals for KHRV150/12RH

Brands by name

Popular brands

Kair KHRV150/12RH, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for KHRV150/12RH

Reviews:

Related manuals for KHRV150/12RH

Brands by name

Popular brands