RU
7
D
E
FÜR DEN INSTALLATEUR
MONTAGE DER WANDHALTERUNG
•
Auf der Wand eine senkrechte Linie in der Mitte
des Kochfeldes zeichnen.
•
Wandhalterung der Dunstabzugshaube
1
an die
Wand symmetrisch der Linie legen
. Der Abstand
zwischen den Bohrungen
der Wandhalterung
1
und dem Kochfeld soll mindestens 1062 mm
betragen. Achten Sie auf waagerechte
Positionierung. Markieren Sie den Abstand
zwischen den Öffnungen an der Wand.
•
In der Wand an der markierten Stellen Bohrungen
mit entsprechendem Durchmesser erzeugen
(achten Sie auf das Durchmesser der
beiliegenden Dübeln), Dübel einschlagen und
das Gerüst an der Wand befestigen.
MONTAGE DER DUNSTABZUGSHAUBE
•
Auf die
W
andhalterung
1
die Dunstabzugshaube
2
auf
hängen und mit den Schrauben
3
waagerecht positionieren. M
it
der Schraube
4
vor
dem Herunterrutschen sichern
.
•
soll
en
1
Kohlefilter
(
300 × 280 × 10
m
m
)
oder 2 (je
nach Modell) Kohlefilter
(
230 × 280 × 10
m
m
)
gekauft und installiert werden (seihe die Seite 25)
.
•
Auf die Dunstabzugshaube
2
die Teleskopkamin-
Blende
5
anbringen
.
•
Die
Teleskopkamin-Blende
5
auf die gewünschte
Höhe her
aus
schieben und ihre maximale
Position auf der Linie markieren. Teleskopkamin-
Blende wieder entfernen
.
•
In
63 mm von der Markierung des maximalen
A b s t a n d e s
d i e
W a n d h a l t e r u n g d e r
Teleskopkamin-Blende
6
pla
tz
ieren, Abstand
zwischen den Montageöffnungen markieren und
die Wandhalterung befestigen. Falls notwendig
auch die
Verschlussklappe
7
mit den selben
Schrauben montieren
.
•
Teleskopkamin-Blende wieder anbringen und mit
g e e i g n e t e n S c h r a u b e n a n d i e
Dunstabzugshaube und Obergerüst befestigen
.
•
Die Dunstabzugshaube an das S
trom
netz
anschließen
.
•
Montieren Sie die V-Klappe
8
an die
Außenöffnung.
•
Bei dem Abluftbetrieb der Dunstabzugshaube
soll auf die installierte V-Klappe
8
das Abluftrohr
mit 150 mm Durchmesser montiert werden. Bei
der Montage eines Abluftrohres mit 120 mm
Durchmesser verwenden Sie den Adapter
9
.
Bei dem Umluftbetrieb der Dunstabzugshaube
ИНСТРУКЦИЯ ПО МОНТАЖУ
MOНТАЖ НАСТЕННОГО КРОНШТЕЙНА
•
Начертить на стене вертикальную линию,
обозначающую центр плиты
.
•
Приложить к стене кронштейн подвески
воздухоочистителя
1
, установить его симметрично
по средней линии, причем расстояние между
отверстиями на кронштейне
1
и нагревательной
плитой, должно составлять минимум 1062 мм.
Установить его по горизонтали, обозначить на стене
расстояние между монтажными отверстиями
.
•
В ы с ве рл и т ь в о б оз н ач е н н ы х м е с та х
от в е р с т и я , п р и м е н я я с в е рл о д и а м ет р о м
соответствующим диаметру дюбелей. Забить
дюбели, а затем привернуть к стене профиль
подвески.
MO
НТАЖ
ВОЗДУХООЧИСТИТЕЛЯ
•
На установленном кронштейне
1
повесить
корпус воздухоочистителя
2
и при помощи
болтов
3
, установить его по горизонтали.
Завернуть винт
4
для надёжного крепления
устройства
.
•
На выходное отверстие установите
-клапан
8
.
•
Для
работы
воздухоочистителя в режиме
вытяжной системы на установленный
V
-
клапан
8
следует монтировать вытяжную
трубу диаметром 150 мм. При подключении
трубы диаметром 120 мм используйте
переходник
9
.
•
В случае работы
воздухоочистителя в режиме
рециркуляции необходимо приобрести
1
угольный фильтр
мм) либо
2
(в
зависимости от модели) угольных фильтра
мм) и установить их (см стр. 25).
•
На повешенный воздухоочиститель
2
, надеть
декоративный кожух
5
.
•
Декоративный кожух
5
раздвинуть до
т р е б у е м о й в ы с о т ы , о б о з н а ч и т ь е г о
максимальное расстояние на средней линии,
а затем снова его снять
.
•
На расстоянии 63 мм
o
т обозначенного
максимального расстояния, приложить к
средней линии держатель декоративного
кожуха
6
,
обозначить на стене расстановку
монтажных отверстий и установить его. В
случае необходимости, установить заглушку
7
, пользуясь теми же монтажными болтами
.
•
Вновь установить верхний декоративный
кожух и, при помощи соответствующих
винтов, закрепить ее к корпусу вытяжки и
верхнему держателю.
•
П о д к л ю ч и т ь в о з д у х о о ч и с т и т е л ь к
электросети.
V
(
300 × 280 × 10
(
230 × 280 × 10