WARNING!
TO REDUCE THE RICK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN, ANY LIQUID OR MOISTURE.
INSPECTION
If these goods are damaged in transit, the
DELIVERING TRANSPORTATION COMPANY
is required by law to make notation of damages on
the freight bill. If in your opinion, there may be concealed damage, they are required to make an inspection after goods are unpacked. Transportation
rates are made in proportion to damage. Therefore, the carrier and
NOT
the shipper should be charged with any loss or damage. Any claim should
be filed with the delivering Transportation Company.
PLEASE DO NOT RETURN GOODS TO US WITHOUT OUR RGA NUMBER AND
SHIPPING INSTRUCTIONS.
Electrical: CAUTION:
Voltage changes require wiring changes at drive motor.
WARRANTY DOES NOT COVER
unauthorized wiring
changes/failures.
Consult an electrician an electrician if your not familiar with electrics.
K16-18 SETUP
•
BEFORE STARTING OR CONNECTING ELECTRICAL VERIFY THE PHASE AND VOLTAGE OF THE UNIT.
•
BE SURE MACHINE IS BALANCED CORRECTLY SO IT WILL TIP OVER.
•
TO GUARD AGAINST CONCEALED DAMAGE, STAND CLEAR AND OBSERVE UNIT FOR THE FIRST FEW MINUTES OF
OPERATION. GUARDS MUST NEVER BE REMOVED.
•
BEFORE INSTALLING THE ABRASIVE WHEEL CONFIRM THAT THE CUTOFF WHEEL IS DESIGNED TO RUN AT 2500 SFPM
(MOS). YOU CAN FIND THIS INFORMATION DIRECTLY ON THE THE SIDE OF YOUR CUTOFF WHEEL. IT
ABRASIVE SAW SAFETY
•
NEVER REMOVE SAFETY GUARDS FROM MACHINE. DISCONNECT MACHINE FROM POWER SOURCE BEFORE MAKING
ANY MACHINE ADJUSTMENTS.
•
DO NOT USE AROUND FLAMMABLE MATERIALS OR LIQUIDS.
•
MACHINES SHOULD BE OPERATED IN VENTILATED AREAS.
•
ALWAYS WEAR SAFETY GLASSES OR A FULL FACE SHIELD FOR PROTECTION.
•
DO NOT USE TOOTHED BLADE WITH THIS SAW AND DO NOT ATTEMPT TO USE STEEL BLADES ON THIS SAW.
•
KEEP HANDS CLEAR OF THE CUTTING AREA.
•
DO NOT WEAR GLOVES OR LOOSE FITTING CLOTHES WHEN OPERATING THIS MACHINE.
•
ALWAYS KEEP HAIR TIED BACK OR COVERED.
•
ALWAYS KEEP FLANGES CLEAN AND TIGHT AGAINST CUTTING WHEEL.
•
MANUALLY TIGHTEN AND LOOSE SPINDLE NUT.
•
DO NOT USE IMPACTED GUN TO LOOSEN OR TIGHTEN SPINDLE NUT.
•
ALWAYS KEEP WHEEL GUARD IN THE DOWN POSITION.
•
BE SURE WORK PIECE IS CLAMPED SECURELY IN VISE BEFORE CUTTING.
WARNING!!!!
IMPROPER USE MAY CAUSE BREAKAGE AND SERIOUS INJURY.
DO
1.
DO always handle and store wheels in the vertical position.
2.
DO visually inspect all wheels before mounting for possible
damage.
3.
DO check machine speed against the established maximum safe
operating speed marked on the wheel.
4.
DO check mounting flanges for equal and correct diameter.
5.
DO use mounting blotters when supplied with wheel.s
6.
DO always use a safety guard covering a least one-half of the
abrasive wheel.
7.
DO allow newly mounted wheels to run at operating speed, with
guard in place, for at least one minute before cutting.
8.
DO always wear safety glasses or some type of eye protection
when cutting.
9.
DO tie back hair.
DON'T
1.
DON'T use a cracked wheel or one that has been dropped or has
become damaged.
2.
DON'T force a wheel onto the machine or alter the size of the
mounting hole if wheel won't fir the machine.
3.
DON'T ever exceed maximum operating speed established for
the wheel.
4.
DON'T use mounting flanges on which the bearing surfaces are
not clean, flat and free of burrs.
5.
DON'T tighten the spindle nut excessively.
6.
DON'T start the machine until the wheel guard is in place.
7.
DON'T jam work into wheel.
8.
DON'T force cutting so that motor slows noticeable or work gets
hot.
9.
DON'T wear gloves and or have loose clothing when operating
machine.
10. DON'T use tooth blade on saw.
Summary of Contents for K16-18
Page 4: ...X Y inch...
