English–
4
Bosch eBike Systems
0 276 001 SAI | (14.8.13)
Switching the Push-assistance mode On/Off
The push-assistance feature makes it easier to push the
eBike. The speed in this function depends on the set gear and
cannot exceed 6 km/h (max.). The lower the set gear, the low-
er the speed in the push-assistance function (at full output).
The push-assistance function may only be used when
pushing the eBike.
Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
To
activate
the push-assistance function, press and hold the
“WALK”
button
14
on the operating unit. The eBike's drive is
activated.
The push-assistance function is
switched off
as soon as any
of the following incidents occur:
– You release the
“WALK”
button
14
,
– The wheels of the eBike are blocked (e. g., through braking
or running against an obstruction),
– Your speed exceeds 6 km/h.
Back-pedalling function (optional)
For bikes with back-pedalling function, the pedals rotate
when the push aid is switched on. If the rotating pedals are
blocked, the push aid switches off.
Switching the Lighting On/Off
In the version in which the driving light is powered via the
eBike system, you can use the
2
button on the HMI to simulta-
neously switch the front light and rear light on and off.
When the lighting is switched on
“Lights on”
appears and
when the lighting is switched off
“Lights off”
appears for ap-
prox. 1 s in the text indication
d
. The illumination symbol
c
is
displayed when the light is on.
Switching the driving light on and off has no effect on the back
lighting of the display. The back lighting of the display is active
as soon as the system or the display is switched on.
Speed and Distance Indication
The
speed indication
f
always displays the current speed.
The following functions are available in the
function indica-
tion
(combination of text indication
d
and value indication
e
):
–
“Range”:
Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
–
“Distance”:
Distance covered since the last reset
–
“Trip time”:
Trip time since the last reset
–
“Avg. Speed”:
Average speed achieved since the last reset
–
“Max. Speed”:
Maximum speed achieved since the last
reset
–
“Clock”:
Current time
–
“odometer”:
Display of the total distance travelled with
the eBike (not resettable)
To
switch between the indication functions
, press the
“i”
button
1
on the HMI or the
“i”
button
11
on the operating unit
until the desired function is displayed.
To
reset
“Distance”
,
“Trip time”
and
“Avg. Speed”
, switch
to any of the three functions and then press and hold the
“RESET”
button
6
until the indication is set to zero. This also
resets the values of the other two functions.
To
reset
the
“Max. Speed”
, switch to this function and then
press and hold the
“RESET”
button
6
until the indication is set
to zero.
To
reset
“Range”
, switch to this function and then press the
“RESET”
6
button until the display is reset to the value of the
factory setting.
When the HMI is removed from the holder
4
, all function val-
ues remain stored and can be viewed.
Displaying/Adapting Basic Settings
The basic settings can be displayed and changed no matter if
the HMI is in the holder
4
or not.
To access the basic settings menu, press and hold the
“RESET”
button
6
and the
“i”
button
1
until
“Configuration”
is displayed in text indication
d
.
To
switch between the basic settings
, press the
“i”
button
1
on the HMI until the desired basic setting is displayed. When
the HMI is inserted in holder
4
, you can also press the
“i”
but-
ton
11
on the operating unit.
To
change the basic settings
, press the On/Off button
5
next
to the
“–”
indication to decrease the value or scroll down, or
the illumination button
2
next to the
“+”
indication to increase
the value or scroll up.
When the HMI is inserted in holder
4
, you can also change the
values with the
“–”
button
12
or the
“+”
button
13
on the op-
erating unit.
To exit the function and store a changed setting, press the
“RESET”
button
6
for 3 s.
The following basic settings are available:
–
“unit km/mi”:
The speed and distance can be displayed
either in kilometres or miles.
–
“time format”:
The time can be displayed either in the
12 hour or 24 hour format.
–
“clock”:
The current time can be set here. Pressing and
holding the setting buttons fast-forwards the setting
speed.
–
“English”:
The language for text indication can be
changed. The available languages are German, English,
French, Spanish, Italian and Dutch.
–
“power-on hours”:
Indicates the total travel duration with
the eBike (not changeable).
–
“wheel circum.”
: You can change this value pre-set by the
manufacturer by ±5%.
OBJ_BUCH-2074-001.book Page 4 Wednesday, August 14, 2013 12:19 PM
Summary of Contents for Bosch Active Line
