background image

HOMEOWNERS GUIDE

  Bath with Airjets

1096755-5-

D

12 of 16

Questions? Problems? For additional assistance, please contact KALLISTA’s Customer

Service Department at 1-888-4-KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.

Symptoms

Probable Causes

Recommended Action

7. Blower motor runs but no air 

bubbles are formed.

A. Blower motor inlet is blocked.

 A. Clean blower motor inlet.

B. Air jets are clogged.

B. Use a small between-the-teeth 

dental brush and white vinegar. 
Dip the brush in the vinegar, 
brush the hole, rinse the brush 
in clean water, and then use the 
wet rinsed brush to rinse the 
hole.

C. Check valve does not work.

C. Replace the check valve. Refer 

to your installer or wholesale 
dealer.

D. Blower motor does not work.

D. Replace the blower motor. Refer 

to your installer or wholesale 
dealer.

E. Control does not work.

E. Replace the control. Refer 

to your installer or wholesale 
dealer.

8. Blower motor operates, air 

bubbles are formed, zone 
controls work, but variable 
speed feature does not work.

A. Blower motor inlet is blocked.

A. Clean blower motor inlet.

B. Loose, disconnected, or 

damaged wiring harness.

B. Check wiring for proper 

connections. Replace the wiring 
harness if necessary. Refer 
to your installer or wholesale 
dealer.

C. User keypad does not work.

C. Replace the user keypad. Refer 

to your installer or wholesale 
dealer.

D. Blower motor does not work.

D. Replace the blower motor. Refer 

to your installer or wholesale 
dealer.

E. Control does not work.

E. Replace the control. Refer 

to your installer or wholesale 
dealer.

Summary of Contents for P50045-G5

















Reviews: