39
GB
Charge pellet
Fuel is loaded from the upper part of the stove by opening
a door. Pour the pellets in the hopper. When empty, it will
hold slightly more than 23 kg.
This is easier if performed in two steps:
• Pour half of the contents of the bag into the hopper and
wait for the fuel to settle on the bottom.
• Then pour in the rest.
The brazier should be cleaned before each
starting.
Never remove the protection grille in the
hopper. When filling, do not let the sack of
pellets touch any hot surfaces.
Remove any components which might
burn from the firebox and from the glass
(various instructions and adhesive labels).
First lighting of the stove
• Before switching on, make sure that the grate is clean and
empty of any pellet residues from previous combustions.
Otherwise make sure you empty and clean it
• Fill the container 3/4 full with the pellets recommended
by the manufacturer
• Connect the stove to an electrical outlet with the cable
that has been supplied
• Press the lighting switch located on the back part of the
stove
• The upper display will read “
O F F
”
• Press the button for 2 seconds. After a few moments
the smoke extractor and the lighting resistor will start
and the display will read “
S T A R T
”; The led resistance is
switched on
• After 1 minute the display will read “
L O A D P E L L E T
”, the
stove will load the pellets and continue lighting the resistor
• Once the appropriate temperature has been reached
the display will read “
F L A M E L I G H T
”: this means that the
stove has begun the last phase in lighting, at the end of
which the stove will be completely operational; The led
resistence is switched off
• After some minutes the display will show the words
“
W O R K
”
alternating room temperature and current working
power. The stove is now completely on
• When the stove reaches the set temperature, the display
will show “
M O D U L A T I O N
”
.
Stove start up
We highly recommend to turn to our
Authorized Service Centre for the
installation and the first ignition of the
device as it not only carries out the installation
perfectly but also verifies the regular operation of it.
During the first lighting the environment should
be well ventilated since during the first hours of
operation unpleasant odours could develop due to
the physical stabilizing of the paint and from the
grease in the tube bundle.
Before lighting a small amount of smoke
may fill the combustion chamber.
Stove switching off
To switch off the stove, press the key
on the control
board until you read “
C L E A N I N G F I N A L
” on the display.
After the stove has been switched off, the fan continues
working for a set time in order to grant a fast smokes
exhaust from the combustion chamber.
If you have a model with remote control, you just need to
switch the remote control off keeping the key pressed for
2 seconds and confirming the selection pressing the key
SEND.
If you try to switch on the stove during this phase, the
display will show “
w a i t i n g c o o l i n g
” (that means wait for
cooling) in order to inform you a switching off phase is
running. Wait until the cooling phase is completely off and
the display shows “
O F F
” before staring a new light up.
REMARKS
:
• Do not continuously turn the stove on and off as this
could provoke sparks that could shorten the life of the
electrical components.
• Do not touch the stove with wet hands: the stove
has electrical components that could produce sparks
if handled incorrectly. Only authorized technicians can
resolve possible problems.
• Do not remove any screws from the fire chamber without
first lubricating them well.
• Never open the glass door of the pellet stove while the
stove is in operation.
• Be sure that the brazier basket is positioned correctly.
• The flue system must be suitable for inspecion. If it cannot
be removed, it must have some holes for inspection and
cleaning.
Summary of Contents for Denia 14
Page 1: ...INSTALLER USER MANUAL For Denia 14 14D Mia 16 16D...
Page 28: ...55 GB NOTES...
Page 29: ...56 GB NOTES...
