Kalor Denia 14, Installer And User Manual

45

GB

Display informations

Alarm signals

OFF

The stove is off.

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

START

The stove is switching on. 
Resistance and smokes extractor 

are on.

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

LOAD PELLET

The stove starts loading pellets in 
the brazier. 
Resistance, smokes extractor and 

gear motor are on. 

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

FLAME LIGHT

The stove starts loading pellets in 
the brazier. 
Smokes  extractor  and  gear  mo-

tor are on.

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

CLEANING FIRE-POT

The stove is cleaning the brazier. 
The smokes extractor is working 
at its max. speed and the pellets 

loading is minimal. 

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

WORK

The  stove  is  working,  in  this  case 
with  working  power  3.  Detected 
room temperature is 21°C. Smokes 

ventilator, gear motor and room 

ventilator are on during this phase.

21:10

22°C    

P-1

OFF

14:35

21°C     

P-2

START

14:35

21°C     

P-2

LOAD

pellet

14:35

21°C     

P-2

FLAME

LIGHT

15:18

21°C     

P-3

WORK

(5)

16:40

22°C    

P-2

CLEANING

FIRE-POT

Regular checks should be carried out by the user, who should only contact the Authorized Assistance Center 
if no solution is found.

In the event of a working defect, the system informs the user about the type of failure occurred.
The following table summarises the alarms, kind of problem and possible solution:

Upper

Display

Lower

Display

Kind of failure

Solution

AL 5

The cannot start up
This is the first light-up

Fill in the tank with pellets
Start up again

AL 6

NO

PELLET

The pellet stove switched off while  work-

ing

Fill in the tank with pellets

AL 2

PROBE

EXHAUST

The smokes sensor is broken or not 
connected to the pcb

Contact an Authorized Assistance Center

AL 7

SAFETY

THERMAL

The stove is overheated

Reset the thermostat manually. If the problem persists, 

contact an 

Authorized Assistance Center.

COOL

FIRE

There is no power supply

As soon as the power supply is back, the stove starts a cool-
ing cycle. After completing the cycle it starts working auto-
matically

AL 4

FAN

FAILURE

Smokes extractor blocked or broken

Contact an Authorized Assistance Center

AL 8

FAILURE

DEPRESS

Obstructed flue

Clean the flue or check there are no obstructed grids near the 
smokes exhaust

SERVICE

The stove has worked for 1300 hours. 
Supplementary maintenance required

Contact an Authorized Assistance Center