background image

31

GB

Charge pellet

Fuel is loaded from the upper part of the stove by opening 

a door.

Pour the pellets in the hopper; vacuum contains about 23 
kg of pellets. This is easier if performed in two steps: 
• Pour half of the contents of the bag into the hopper and 
wait for the fuel to settle on the bottom.
• Then pour in the second half;
• Keep the cover closed , after loading the pellets , the lid 
of the fuel tank;
• Before closing the door load-pellet make sure that there 
are  no  residues  of  pellets  around  the  seal.  If  carefully 
cleaned to avoid compromising the seals.

The stove is a product by heating, presents the external 
surfaces particularly hot. For this reason, we recommend 
extreme caution when operating in particular:
• Do not touch the stove body and the various compo-
nents, do not approach the door , it could cause burns;
• Do not touch the exhaust fumes;
• Do not perform any type of cleaning;
• Do not dump the ashes;
• Do not open the ash tray;
• Be careful that children do not come near;

•  The  appliance  is  not  intended  for  use  by  persons 
(including  children)  with  reduced  physical,  sensory  or 
mental capacities , or lack of experience or knowledge, 
unless  they  have  been  given  through  the  intermediary 
of  a  person  responsible  for  their  safety,  supervision  or 
instruction concerning use of the appliance;

• Do not use the stove as a ladder or scaffold;

•  Do  not  put  clothes  to  dry  on  the  stove.  Any  clothes 
hangers  and  suchlike  must  be  kept  a  suitable  distance 
from the stove. - Risk of fire 

•  Carefully  explain  that  the  stove  is  made  from  material 
subjected  to  high  temperatures  for  the  elderly  ,  the 
disabled, and in particular for all children, keeping them 
away from the stove during operation

• Do not touch the stove with wet hands: the stove has 
electrical  components  that  could  produce  sparks  if 
handled incorrectly.

• Never open the glass door of the pellet stove while the 

stove is in operation.

•  The  stove  must  be  connected  to  an  electrical  system 
equipped with an earthing conductor in accordance with 
regulations 73/23 and 93/98 EEC;

•  The  system  must  be  of  adequate  electrical  power 
declared the stove;

• Do not wash the inside of the stove with water.
The water could damage the electrical insulation, causing 
electric shock;

• Do not expose your body to hot air for a long time. Do 
not overheat the room you are in and where the stove is 

installed.

This  can  damage  the  physical  conditions  and  cause 
health problems;

•  Do  not  expose  to  direct  the  flow  of  hot  air  plants  or 

animals;

• The pellet stove is not a cooking element;

•  External  surfaces  during  operation  can  become  very 
hot.  Do  not  touch  them  except  with  the  appropriate 

protection.

Instructions for safe and efficient use

Never remove the protection grille in the 

hopper. When filling, do not let the sack 
of pellets touch any hot surfaces.

Summary of Contents for Denia 14






























Reviews: