background image

Manual: CMOS Industrial Camera LOGLUX

 i5

Version 1.08 (04/07)



KAMERA WERK DRESDEN GmbH

Page 21 of 46

The ‚Sensor‘ profile menu

Sensor-specific  parameters  are  entered  in  this menu.  These  include  the  pixel  clock  rate,  the  shutter
mode, the ADC amplification, and the gamma correction option.

The pixel clock rate of the camera can be set in
the 'Pixel clock' box. The frame readout time is
displayed below the box.
One  of  the  two  sensor  shutter  modes,  i.e.

synchronous  shutter

  or 

rolling  shutter

,  can  be

selected under 'Shutter'.
Under  'Amplification'  the  user  can  set  the
amplification  factor  for  the  analog  amplifier
downstream  of  the  sensor  in  6  increments.
Default is 1.

Note:

 

For 

the 

following 

reasons, 

the

amplification  factor  should  not  be  changed  in
industrial image processing applications:

  The  proper  calibration  of  the  camera  is  no

longer guaranteed.

  The  pixel  values  are  falsified  through  the

amplification limitation.

  The signal noise would be amplified and the

desired  improvement  of  the  image  brightness
cannot be achieved.

Figure 17 : 

The ‚Sensor‘ profile menu

Summary of Contents for CMOS















































Reviews: