Katherm HK
Assembly instructions
EN
Assembly instructions
5
SAP 1521128 01/22
1
Overview
8
1
2
3
6
7
5
9
10
4
1
11
Katherm HK E
Katherm HK at a glance
1
Junction and control box
2
Condensate tray
3
Convector
4
Roll-up grille
5
Height adjustment feet
6
EC tangential fan
7
Filter (optional accessory)
8
Floor trench
9
Load-bearing height adjustment feet
10
Condensate pump mounting kit
11
Convector with integral electric coil and safety
chain
2
Safety
This section provides an overview of all important safety aspects for protecting personnel. In ad-
dition to the safety notes in this and the more detailed instruction in accordance with the QR
Code, the occupational health and safety and environmental protection regulations applicable to
the unit's field of application, as well as the notes in accordance with EN60335-1, must be ob-
served.
2.1
Correct use
The units are used for heating and/or cooling all areas of buildings that need to be heated in
winter and cooled in summer due to the high incidence of sunlight through the glass façades.
Within the room, the unit needs to be connected to the building's heating/cooling/ventilation
system and to the building's waste water and power network. The operating limits and limits of
use described in
must be observed.
Intended use of the unit also includes adherence to these instructions.
Any use beyond or other than the stated intended use is considered as misuse.
Any change to the unit or use of non-original spare parts will cause the expiry of the warranty
and the manufacturer’s liability.
2.2
Limits of operation and use
Limits of operation
Min./max. water temperature
°C
5-120
Min./max. air intake temper-
ature
°C
15-40
Min./max. air humidity
%
15-75
Min. operating pressure
bar/kPa
-
Max. operating pressure
bar/kPa
10/1000
Min./max. glycol percentage
%
25-50
Operating voltage
230 V/ 50/60 Hz
Power/Current consumption
On the type plate
IMPORTANT NOTE!
Danger of frost in cooling mode!
There is a risk of the heat exchanger freezing when used in unheated rooms.
Protect the unit from frost.
IMPORTANT NOTE!
Warning of misuse!
In the event of misuse, as itemised below, there is a danger of limited or failing
operation of the unit. Ensure that the airflow can circulate freely.
Never operate the unit in humid areas, such as swimming pools, wet areas
etc.
Never operate the unit in rooms with an explosive atmosphere.
Never operate the unit in aggressive or corrosive atmospheres (e.g. sea air).
Never operate the unit above electrical equipment (such as switch cabinets,
computers or other electrical units, or contacts that are not drip-proof).
Never use the unit as a construction site heater.
2.3
Risk from electrocution!
DANGER!
Risk of fatal injury from electrocution!
Contact with live parts will lead to fatal injury from electrocution. Damage to the
insulation or individual components can lead to a fatal injury.
Only permit qualified electricians to work on the electrical system.
Immediately disconnect the system from the power supply and repair it in
the event of damage to the insulation.
Keep live parts away from moisture. This can cause a short circuit.
Properly earth the unit.
2.4
Personnel requirements - Qualifications
Expertise
The installation of this product requires specialist knowledge of heating, cooling, ventilation, in-
stallation and electrical engineering.
Damage caused by improper installation is the responsibility of the operator or installer. The in-
staller of these units should have adequate knowledge of the following gained from specialist
professional training
Safety and accident prevention regulations
Country-specific guidelines and recognised technical regulations, i.e. Association of German
Electricians (VDE) regulations, DIN and EN standards.
VDI 6022; maintenance personnel must be trained to Category B (possibly Category C) to
comply with hygiene requirements (as required).
2.5
Personal Protective Equipment
Personal protective equipment is used to protect people from impaired safety and health when
working with the unit. The applicable accident prevention regulations at the place of use apply
in all cases.
Assembly, installation and operating
instructions:
Kampmann GmbH & Co. KG
Friedrich-Ebert-Str. 128-130
49811 Lingen (Ems)
T: +49591/7108 0
E: info@kampmann.de
www.kampmann.de
Summary of Contents for Katherm HK
