background image

Installing the device  

 

The ceramic cooker hob must be installed by qualified personnel. 

 

Do not block the ventilation slots of the device. This may overheat the device. Keep a Min. 
distance of 10 cm to walls or other items.  

 

Do not place hotplates next to open fires, heaters or other sources of heat.   

 

Make  sure  that  the  mains  connection  cable  is  not  damaged  or  squashed  beneath  the 
device.  

 

Make sure that the mains connection cable  does not  come into contact  with sharp edges 
and/or hot surfaces.  

 

The device should be connecting to the power source which is sufficient secured since the 
full power is 7200W.

 

 

 

Do  not  install  the  hob  above  a  dishwasher  or  washing-machine,  so  that  the  electronic 
circuits do not come into contact with steam or moisture which could damage them. 

 

 

 

Commissioning the device  

 

Prior to connecting the device, check whether the voltage indicated on the type plate 
corresponds to the voltage supply in your home. A wrong connection may lead to grave 
damage on the device and injury to persons.  

 

The hotplate's surface consists of temperature-resistant ceramics. In case of damage, even if 
this concern only a small tear, disconnect the device from the power supply immediately and 
contact the customer service.   

 

We recommend not placing any metal kitchen utensils, cookware or pan lids, knives or other 
metal objects on the hotplate. These may heat up when the device is turned on.   

 

Do not place any magnetically objects like credit cards, cassettes etc. on the glass 
surface while the device is in operation.  

 

On order to avoid overheating, do not place any aluminium foil or metal plates on the device.    

 

Do not insert any objects like wires or tools into the ventilation slots. Attention: this may cause 
electric shocks.   

 

Do not touch the hot surface of the ceramic field. Please note: the hotplate does not heat up 
itself during cooking, but the temperature of the cookware heats up the hotplate!   

 

Do not heat up any unopened tins on the hotplate. A heated tin could explode; therefore 
remove the lid under all circumstances beforehand.

    

 

Summary of Contents for NCH-7205x















Reviews: