MOUNTING OF 12000XT-HD BOXES
MOUNTING OF 12000XT-HD BOX
5. Connection to the power supply (battery)
Please read the following information carefully before
connecting.
All bolts on the motor are equipped with a nut
and counter nut. When tightening the wires, it is IMPERA-
TIVE to secure the counter nut with the wrench so that the
bolt does not turn. Turning the bolt may damage the internal electrical
connections in the motor.
If the wires delivered with the winch are too short,
enlarge their cross-section in accordance with an
increase in length thereof.
From the wiring diagrams presented below,
choose the one appropriate for your winch model.
Following these instructions, connect the winch to the power supply
according to the diagram.
Step 1.
Connect the free end of the long BLACK wire to the negative (-)
pole of the battery *.
Step 2.
Connect the free end of the long RED wire to the positive (+)
pole of the battery **.
* Always connect the black wire directly to the battery only..
Never use any other grounding available on the vehicle.
**The red wire must be fitted with a safety circuit breaker and
a fuse.. When connecting the fuse, make sure it is properly
installed. There is a marking to indicate which connector should
be connected to the wire to the battery and which to the wire to
the motor.
When routing the wires, make sure that they are not placed
next to movable parts that may break the insulation or wire.
Never place wires on sharp edges that may cut the insulation
or wire. Do not let the wires touch surfaces that may get hot.
All connections should be securely tightened using screws with spring
washers. Inaccurate connections may result in sparks, short circuits
and may supply a too low current to the motor of the winch.
Always protect exposed electrical connections by means
of protector caps and/or copper grease, especially if the
winch is used in adverse conditions.
•
The battery must be in good condition.
•
Make sure that the wires are not exposed to damage by contact,
for example with a hot engine, sharp edges, etc.
•
Corrosion on the connection terminals will weaken the capabilities
of the winch and can cause a short-circuit or damage.
•
Clean all surfaces of connections (contacts) on a regular basis.
•
If you work in a corrosion aggressive environment, use additional
protection on connection terminals.
5
kangaroowinch.eu
Summary of Contents for 12000PS
