background image

Pitts Python 

ARF  

ASSEMBLY MANUAL 

  

 

 

Kangke Industrial USA, Inc. 

49 E. Industry CT, Unit N, Deer Park, NY 11729  

http://www.kangkeusa.com

     E-mail: 

info@kangkeusa.com  

Tel: 1-631-274-3058   Fax: 1-631-274-3296  

This manual is the sole property of Kangke Industrial USA, Inc. Reproducing any part without the consent 
of Kangke Industrial USA, Inc. is a lawful violation.

  

 

Warranty:

 Kangke Industrial USA Inc. guarantees the kit to be free of defects in both material and 

workmanship at the date of purchase. This warranty does not cover any parts damaged by use or 
modifications. In no case shall Kangke Industrial’s liability exceed the purchase cost of this kit. Since 
Kangke Industrial has no control of final assembly and material used by user for final assembly, no 
liability shall be assumed or accepted for any damage resulting from the use by user of final user -
assembled products. This kit has been flight test for normal use. If the plane will be used for extremely 
high stress flying, the modeler is responsible for reinforcing the high stress points. Inspect this kit 
immediately after receiving it, report any missing and damaged parts within 7 business days otherwise 
the claim may be denied.

  

Summary of Contents for Pitts Python ARF



















Reviews: