background image

22

4.8  DCo Check

The Device Configuration Overlay (DCO) is a partition on the hard drive that is not normally visible 

to an operating system. If the Master drive contains a DCO partition, then the DCO may not be 

accessible to the duplicator unless this option is enabled.

Press the 

ENT

 button to change this option.

• 

٭ 

]

 – DCO Check is enabled (default). When DCO CHECK is enabled the duplicator will 

recognize the Device Configuration Overlay area. 

• 

[     ]

 – DCO Check is disabled. The system will not check for DCO partitions. Drives that 

contain a DCO partition may not duplicate successfully. 

4.9  button Sound

The BTN. SOUND option allows you to enable or disable the audible tone that accompanies every 

button press.

Press the 

ENT

 button to change this option.

• 

٭ 

]

 – Button sounds are enabled (default). Button presses and system notifications will be 

accompanied by a short, audible tone. 

• 

[     ]

 – Button sounds are disabled. No audible tones will sound.

4.10  Show EXE Time

The SHOW EXE TIME option allows you to enable or disable whether the total execution time for 

an operation is displayed on the LCD screen. The total execution time will be displayed after an 

operation has completed.

Press the 

ENT

 button to change this option.

• 

[     ]

 – Disabled (default). The total execution time is not displayed.

• 

٭

 ]

 – Enabled. The total execution time is displayed.

DCO Check / Button Sound / Show EXE Time 

Summary of Contents for kclone-5hd-twr
































Reviews: