background image

 

 

                                        

User Manual 

BW-50-070/10

 

 

 

Page 7 of 16  

The Water Mattress 

When filled to the level mark it contains about 4.5 litres of water. If you plan to tilt the bed then add 2 cm 

of water. Fill by using the filling tube. Add Anti Algae every 3 months. Water molecules diffuse through the 
material. This is normal. Therefore the water level should be checked regularly 

NOTE: Do not tilt the Water Mattress if the temperature must be higher than 37

O

C. The very 

sensitive over temperature circuit can alarm and switch off the warming. 
When tilting during warming up, too little water will make the over temperature alarm go off. 

Explanation of the drawings on the Water Mattress  

 

9.

 

The level mark on the Water Mattress indicates standard water amount. If tilting is required please 

add 2 cm more water.

 

10.

 

Place the Water Mattress in an upright position and fill it with the enclosed Filling Tube. When the 

desired level has been reached, add Anti Algae carefully through the filling hole or via the Filling 

Tube. Follow the caution instruction on the Anti Algae package. 

NOTE: Air pressure may build 

while filling. Interrupt filling and release air if necessary.

 

 

11.

 

Remove air bubbles, Very Important. Place the Water Mattress on a flat surface and lift the filling 

hole 5 to 10 cm upwards. Press the air bubbles towards the hole repeatedly until all major air 
bubbles are expelled. 

12.

 

Lower the filling hole while pressing the Water Mattress so that no air enters and insert the plug. 

13.

 

Turn the Water Mattress upside down and insert the Heating Pad in the pocket.  

14.

 

The Water Mattress and the Heating Pad is inserted into the KANMED Baby Nest. 

 

 

The KANMED Baby Nest 

Different types of KANMED Baby Nests are available. Please check with your supplier or on internet 

www.KANMED.se 
 

The KANMED Baby Nest is intended to prevent the baby from rolling off the water mattress, to facilitate 

correct positioning and to create a tight and cosy environment around the baby. 

By pulling the strings one can adjust the collar from being wide open and flat to become a tight raised wall 
around the baby. The Baby Nest consists of a bag into which the Water Mattress and Heating Pad is 

inserted.  

Note:

 Check the Baby Nest regularly for damages. To reduce the risk of a nest splitting during washing we 

recommend that the nest is used for only one year. 

 

 
 

 ! 

Summary of Contents for BABYWARMER

















Reviews: