background image

USER and TECHNICAL MANUAL KANMED Warming Cabinet GE-2-1370     

Page 3 of 16 

 
 

1 SAFETY 

INSTRUCTIONS 

 

INTENDED USE

 

KANMED Warning Cabinet GE-1380-XX is primarily intended for warming of Gel Pads, 
blankets, fluids,  up to a temperature of 42

°

KANMED Warning Cabinet shall be used according to this user manual and in accordance 
with normal hospital routines. 
 
 

GENERAL ADVICE 

Adjust the cabinet so that it is correctly positioned, vertically and horizontally. 
Secure the cabinet to the wall using the built in brackets at the top. 
Never pull out all shelves/baskets at the same time. The cabinet can tilt forward if it is not 
secured to the wall. 
 
Take extra caution if the cabinet is mounted on wheels, especially when the cabinet is moved 
around.  

Note!

 If the cabinet is not secured to a wall, don’t’ pull out more than 

one 

shelf/basket at a 

time.  
 
Do not overload the shelves/basket - maximum 8 kilos per shelf. Max 2 pcs. of gel pads 
(45x50x1.5) Max load of the basket is 20kg. 
Do not overfill the 

top shelf - 

there must be at least 5 cm's free space to ensure air 

circulation. 
Don't block the ventilation holes at the inside rear of the cabinet. 
 
 

EXPLANATION OF SYMBOLS

 

 
 
 

Consult Users Manual 

 
 

  O 

OFF 

 

   I

 ON 

   

~

 AC 

current 

 
 
 

UP button, rises temperature 

 
 
 

DOWN button, decreases temperature 

 
 
 

SET button, for displaying desired temperature 

 
 
 
 

Summary of Contents for GE-1380

















Reviews: