background image

                     

  

User manual WC

 

 

 

Page 

13 of 20

 

 

6 Cleaning, Checks before use and Maintenance 

 

General information 

The WarmCloud control unit, hoses and remote control should be carefully cleaned between each 
patient. 
Follow the routines set forth by the person responsible for cleaning and disinfection in your hospital 
and department and according to the instructions below. 
Inspect all parts for wear and damages before and after cleaning.  
Below is a list of cleaning and disinfection agents recommended by Kanmed. Using other agents 
and/or exaggerated cleaning may reduce the lifetime of some or all parts. Contact Kanmed with 
the product specification if in doubt. 
Do not use bleach and solvents. 
Kanmed recommends using the Kanmed Tube Protection Art no 700-0882 
 

Cleaning:

 Use soap water in a moist cloth. 

 

Disinfection:

 The WarmCloud, Remote control with cable and hose set withstands most common 

surface disinfectants used in hospitals. Kanmed recommends DAX surface disinfectant which is 
alcohol based. Do not use alcohol based solutions stronger than 70%  
If in doubt, try on a small surface or contact your distributor or Kanmed. 
 

Hose protection 

Kanmed Disposable Tube Protection Art no 700-0882 is available to facilitate keeping the hoses 
clean. 
 

WarmCloud Mattresses 

The Mattress is a single patient use disposable item and shall not be reused. 

Checks before use 

Check that all parts are clean and in good condition. Check that the hoses are properly connected 
to the unit by pulling gently. Check that the unit performs a self-test at start. If Error Codes appear 
and cannot be eliminated with the suggestions given in section 10 then you shall not use the unit. 
Note: If the Main Unit or hose set has received mechanical damage, it should always be checked 
and correct system function verified by technical staff. 
 

Maintenance 

Kanmed WarmCloud does not require any special maintenance apart from annual check according 
to the service manual. 
 

7 Accessories and Spare Parts 

 

Article no 

Product 

Comment 

9000 

Kanmed WarmCloud 

Complete system with standard accessories. 230V 

9000-120 

Kanmed WarmCloud   

Complete system with standard accessories. 120V 

OT-600-222 

Warm-Air Mattress, 
Wide 

Single-Use Mattress with ties, Length 200 cm, Width 55 cm. 
Delivered in box of 10 pcs 

OT-600-211 

Warm-Air Mattress, 
Small 

For “leg

-

up” positions and for Children

 

Single-Use Mattress with ties, Length 110 cm, Width 50 cm. 
Delivered in box of 10 pcs 

700-0882 

Tube protection 

Disposable thin plastic tube 

9300 

Remote control 

 

OT-600-705  Remote control cable 

 

9131 

Wheel base 

Wheel base with tube storage. 

WC2-10 

Hose set complete 

Kit with two tubes 

WC2-070 

Manual 

English Manual. 

9079 

Manual 

Service manual English.  

 

Test box 

For service checks only 

 
 
Other mattress sizes and accessories may be available Always check with your dealer or 

www.kanmed.se

 for the latest information.

 

 

Summary of Contents for WarmCloud





















Reviews: