background image

  

  

 

 

 

 

 

 

6.1

 

Product Warranty  

 

We do not issue product warranties.  

 

A user registration guide is attached to the product. Please follow the instructions 

and complete the user registration on the top page of our website. Once registered, 

we will start the warranty. Please note that without registration, we may not be 

able to guarantee the product.  

The warranty period for quality problems caused by operation 
according to the instruction manual is 3 years from the date of 
purchase.  

 

6.2

 

after-sales service  

 

If you're not feeling well, check first...  

Please read the section "5. If you think the product is malfunctioning, please read "5.  

 

Still, if you're not feeling well...  

Please contact the distributor, Kanomax Japan K.K. (see last page), or the 

distributor where you purchased the product.  

 

Repairs under warranty are...  

If the failure is caused by our manufacturing, circuit components, or materials, we 

will repair it free of charge.  

 

Repairs after the warranty period has expired are...  

If the function and accuracy can be maintained by repair, we will repair it at your 

request for a fee.  

 

Retention period for repair parts...  

Repair parts will be held for a minimum of 5 years after discontinuation of production.  

This is the period during which the parts are available for repair. For details, please 

contact the distributor, Japan Kanomax Co.  

  

 

 

 

 

 

 

6. Product Warranty and After-Sales Service  

Summary of Contents for 3720-06
























Reviews: