background image

11

Specifications

 

Tweeters 

1 inch Silk Dome

 

Woofers 

4 inch Kevlar®

 

Nominal Impedance 

4 Ohm

 

Amplifier Type 

Class D

 

Power Output 

140 Watts Peak

 

Input Sensitivity 

560 mV

 

Total Harmonic Distortion 

< 0.25% 

 

Crossover System 

2-way

 

Crossover Frequency 

2.0 kHz

 

Frequency Response 

60Hz – 20kHz

 

Inputs 

1 x 3.5 mm stereo mini-jack AUX

 

 

1 x RCA L/R 

 

 

2 x Optical (Toslink)

 

 

1 x Bluetooth® 4.0 with Qualcomm aptX

 

Outputs 

1 x Subwoofer

 

 

1 x USB Charge Port 5 V 1.0A

 

Speaker Terminals 

Left and Right Binding Posts

 

Input Voltage / Frequency 

AC 100 V - 240 V 50/60 Hz (auto switching)

  Standby Power Consumption 

< 0.5 W

 

Remote Included

 

Dimensions (each speaker) 

W 5.5”x H 8.7” x D 7.5” (140 x 220 x 190 mm)

 

Net Weight (Active) 

6.9 lb (3.2 kg)

 

Net Weight (Passive) 

5.5 lb (2.5 kg)

 

Gross Weight 

16.5 lb (7.5 kg) (boxed pair)

YU4 POWERED SPEAKER SYSTEM

NOTICE:

 

The Bluetooth

®

 word mark and logos are registered trademarks owned by Bluetooth SIG, 

Inc. and any use of such marks by Kanto Distribution Inc. is under license.

NOTICE: 

Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is 

a trademark of Qualcomm Incorporated, registered in the United States and other countries, used 

with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in 

the United States and other countries, used with permission. 

NOTICE:

 This appliance is labeled in accordance with European Directive 2002/96/

EC concerning waste electrical and electronic equipment (WEEE). This label indicates 

that this product should not be disposed of with household waste. It should be 

deposited at an appropriate facility to enable recovery and recycling. 

Summary of Contents for YUP4













Reviews: