background image

User guide

Safety instructions

© 2013 Deko-Light Elektronik-Vertriebs GmbH  

22.12.2014

All rights reserved. 

 

www.deko-light.com
deko@deko-light.com  

page 1 von 1

 - The enclosed from the manufacturers operating user guide / safety instructions / data sheet are required for a 

proper use. Technical changes are reserved.

 - The warranty will not cover damage caused by non-observance of the user guide / safety instructions / data 

sheet. The manufacturers and distributors, don’t take over for consequential damages result from any liability.

 -

This product may only be installed by qualified staff. 

 -

To ensure proper installation / wiring, you must comply with the standard specifications of your country.

 -

All service and maintenance (if applicable) should be performed only by qualified staff.

 -

Disconnect the power supply before installation or modification work and secure it against being switched on 

again. Make sure that all components are free of voltage. 

 - All electrical connections must be tightened and tested annually for tightness. 

 - The lamps must be changed only in cold condition. Risk of burns. Before changing the lamp, the power supply 

must be disconnected.

 -

The mounting and installation close to flammable materials is prohibited.

 -

If damage (eg faulty power line) or a malfunction may be present, disconnect the power supply and contact 

your supplier. Defective parts may be replaced only by qualified staff and with original spare parts.

 - Caution! The package may contain any small parts / packaging materials which can be swallowed by children.

 - The product should not be exposed to strong mechanical loads or dirt.  

 - The indicated performance and connection data acc. datasheet and rating plate must be complied.

 - When used outside the intended use, the approval of the manufacturer must be obtained.

 - Is the product at the end of its service life, dispose it in accordance with the current legal regulations at the 

communal collection points. Disposal in the household waste is prohibited.

 -

 This luminaire is not suitable for covering with thermally insulated material.

 - The Luminaire is “Only to be installed outside arms reach”.

 -

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the  

manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

 - The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a 

similar qualified person.

 -

 Caution, risk of electric shock

Summary of Contents for 843277


















Reviews: