1. Description of the Kap’SAM®
2. Testing the Kap’SAM®’s state of charge
3. Starting a vehicle
Never disconnect the Kap’SAM®’s when the
start light (
) is on. The Kap’SAM® stops
automatically after 30 seconds or can be
stopped at any time by pressing on the ON/OFF
button (
).
The Kap’SAM® is a jump starter for vehicles with a flat battery. To
avoid any malfunctions, it is indispensable to check the connection
polarities when attaching the Kap’SAM® clips to the broken down
vehicle. The device is equipped with reverse polarity protection. If
it is not connected correctly to the vehicle’s terminals, the integrated
PCB will prevent the device from starting up and it will not be
possible to start the vehicle. If the device is connected up wrongly,
a red LED comes on on the user interface.
To connect the Kap’SAM®’s clips to the vehicle, proceed as follows:
The battery terminal not connected to the chassis (usually the red
terminal) must be connected first. The other connection (usually the
black terminal) must be made on the chassis well away from the
battery and from any fuel pipe.
After the charging operation, remove the chassis connection (black
terminal) and then the battery connection (red terminal) in the order
indicated.
Technical data
Voltage
12 Volts
Weight
8.5 kg
Cable cross section
35 mm²
Fuse
300 A
Capacitance
500 farads
STANDARD USE
1
Press the Test button.
2
The charge indicator comes on temporarily and then the Kap’SAM®'s state of charge is displayed. If nothing
appears, this means the Kap’SAM® is completely discharged. In this case, see paragraph on Recharging the
Kap’SAM®.
3
Green indicator:
The Kap’SAM® is fully charged, so its starting capacity is optimum.
4
Orange indicator:
The Kap’SAM® is not completely charged, but it is still possible to start a vehicle. In this case,
you are advised to recharge the Kap’SAM® as described in the paragraph on Recharging the Kap’SAM®.
5
Red indicator:
the Kap’SAM® is discharged. It must be recharged. (See the paragraph on Recharging the
Kap’SAM®).
1
Connect the Kap’SAM®'s clips to the broken down vehicle's battery, making sure you check the polarities.
The vehicle ignition must not be on.
2
Press the
ON
button.
3
The start light comes on.
4
Start the broken down vehicle.
5
After the Kap’SAM® stops:
-Disconnect the Kap’SAM®’s clips from the vehicle
-Roll up the cables and stow the clips in the place provided.
EN
9
8-
Summary of Contents for XCAP-500
