-
5
Î
Pull out the steering wheel, align and in-
sert back.
Î
Fasten the steering wheel using en-
closed nut.
Î
Insert the cover in the steering wheel.
Î
In appliances without battery: Install
batteries.
Î
Connect the battery plug to the appli-
ance.
Î
Step on the standing platform.
Î
Release emergency-stop button by
turning.
Î
Set main switch to “1”.
Î
Set the speed to limited on the pro-
gramme selection switch (MIN).
Î
Set the drive direction to backwards us-
ing the drive direction button at the op-
erator console.
Note
The driving direction switch is also used as
a safety switch. Therefore, this switch must
be pressed even if the desired driving di-
rection has already been set.
Î
To drive, press the accelerator pedal
carefully and drive down slowly from the
palette.
Î
Set main switch to “0”.
Î
Attach hubcaps to the rear wheels.
The brushes must be installed before the
initial operation (see "Maintenance work").
Danger
Long hours of using the appliance can
cause circulation problems on account of
vibrations.
It is not possible to specify a generally valid
operation time, since this depends on sev-
eral factors:
–
Proneness to blood circulation deficien-
cies (frequently cold extremities, tin-
gling, numbness).
–
Low ambient temperature. Wear warm
clothes to protect the affected body parts.
–
A firm grip impedes blood circulation.
–
Continuous operation is worse than an
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occur-
rence of the symptoms (e.g. tingling, numb-
ness in certain body parts) please consult a
physician.
Note
Take the foot off the aceelerator pedal,
press the emergency-stop button to imme-
diately deactivate all functions and turn the
key switch to the "0" position.
Î
Carry out maintenance jobs "Before
starting working week" (see section
"Maintenance and Care").
Danger
Danger of accident. The immobilizing brake
must always be checked first on an even
surface before starting the machine.
Î
Set main switch to “0”.
Î
Press emergency-stop button.
If the appliance can be moved by hand, the
parking brake is not engaged.
Î
Pull up the reset lever of the parking
break.
If the appliance can still be moved by hand,
the parking break is defective. Shut down
the appliance and call Customer Service.
Danger
Danger of accident. If the appliance cannot
brake adequately while going downhill,
press the emergency stop button.
Î
Open the cover of the fresh water reser-
voir.
Î
Fill in fresh water (maximum 60 °C).
Leave sufficient space for the deter-
gent.
Î
Pour in detergent.
Note
The fresh water reservoir cover can be
used to meter the detergent. Content 60 ml.
Î
Close the cover of the fresh water res-
ervoir.
Note
Fill up the fresh water tank completely be-
fore starting up the machine to ventilate the
water supply system.
If the pipe system is empty, it can take
about 2 minutes till the detergent solution
comes out of the cleaning head.
몇
Warning
Risk of damage. Only use the recommend-
ed detergents. With respect to different de-
tergents the operator bears the increased
risk regarding the operational safety and
danger of accident.
Only use detergents that are free from sol-
vents, hydrochloric acid and hydrofluoric
acid.
Follow the safety instructions for using de-
tergents.
Note
Do not use highly foaming detergents.
Recommended detergents:
Carry out the initial trials in an open surface
so that you familiarise yourself with the ap-
pliance.
Danger
Danger of tipping if gradient is too high.
Î
The gradient in the direction of travel
should not exceed 10%.
Danger of tipping when driving round
bends at high speed.
Danger of slipping on wet floors.
Î
Drive slowly when cornering.
Danger of tipping on unstable ground.
Î
Only use the machine on sound surfaces.
Danger of tipping with excessive sideways tilt.
Î
The gradient perpendicular to the direc-
tion of travel should not exceed 10%.
Î
Step on the standing platform.
Î
Do not press the accelerator pedal.
Î
Release emergency-stop button by
turning.
Î
Set main switch to “1”.
Î
Set the speed range on the programme
selection switch.
Î
Set the drive direction using the drive
direction button at the operator console.
Note
The driving direction switch is also used as
a safety switch. Therefore, this switch must
be pressed even if the desired driving di-
rection has already been set.
Î
Press the accelerator carefully to drive.
Note
The drive direction can also be changed
during the drive. You can thus clean very
dirty surfaces by driving back and forth a
couple of times.
In case of overloading, the drive motor au-
tomatically switches off after a certain peri-
od.
Î
Allow machine to cool down at least for
15 minutes.
Note
The detergent supply and brush drive are
interrupted till further movement if the de-
vice stands at one place for more than 2
seconds.
Î
Step on the standing platform.
Î
Do not press the accelerator pedal.
Î
Release emergency-stop button by
turning.
Î
Set main switch to “1”.
Î
Turn the program selection switch to
the desired cleaning program.
Operation
Check immobilizing brake
Brakes
Filling in detergents
Fresh water
Detergent
Application
Detergent
Routine cleaning of all wa-
ter resistant floors
RM 780
RM 746
Routine cleaning of glossy
surfaces (e.g. granite)
RM 755 es
Routine cleaning and ba-
sic cleaning of industrial
floors
RM 69 ASF
Routine cleaning and ba-
sic cleaning of fine stone-
ware tiles
RM 753
Routine cleaning of tiles in
sanitary areas
RM 751
Cleaning and disinfection
in sanitary areas
RM 732
Removal of coating from
all alkali-resistant floors
(e.g. PVC)
RM 752
Removal of coating from li-
noleum floors
RM 754
Driving
Overload
Cleaning
18
EN
