Kärcher BR 60/95 RS Bp Pack Operating Instructions Manual Download

Page: 19 / 322

English

Press the unlocking key.

Press the accelerator carefully to drive.

Note

The drive direction can also be changed
during the drive. You can thus clean very
dirty surfaces by driving back and forth a
couple of times.

In case of overloading, the drive motor auto-
matically switches off after a certain period.

Allow machine to cool down at least for
15 minutes.

Press again the drive fuse on the oper-
ating panel.

Note

The detergent supply and brush drive are
interrupted till further movement if the de-
vice stands at one place for more than 2
seconds.

Press accelerator pedal and drive to the
surface to be cleaned.

Adjust brush contact pressure using the
Brush Contact Pressure switch (4 stages).

In cleaning mode, the highest speed is lim-
ited to Stage II.

Note

Very dirty floors can be cleaned in two
rounds. In the first work step, the detergent
liquid is applied and brushed in. The vacu-
um bar is raised by pressing the Raise/Low-
er Vacuum Bar switch. In the BD model,
the rear spray guard (Aqua-Mizer) also
needs to be removed. The surface is
cleaned normally in the second step after
the detergent has worked normally.

Note

After raising the cleaning head, drive further
approx. 5 m so that the remaining water is
sucked off.

Park the machine on an even surface.

Turn key to "0" and remove it.

Note

Overflow dirt water tank. The suction flow is
interrupted by the swimmer when the dirt wa-
ter tank is full. Empty the dirt water reservoir.

몇

Warning

Please observe the local provisions regard-
ing the wastewater treatment.

Take the dirt water discharge hose from
the support and lower above a suited
collection device.

Let off dirt water by opening the screw
lid at the discharge hose.

Rinse the dirt water tank with clear wa-
ter.

Clean the swimmer and check the
movement of the swimmer ball.

Rinse the dirt water tank with clear wa-
ter.

Pull out the drain hose for fresh water
(located behind the drain hose for dirt
water) and lower it into a suitable collec-
tion system.

Let off detergent by opening the screw
lid at the discharge hose.

Lift the cleaning head.

Turn key to "0" and remove it.

Loosen the cross-handle of the spray
guard and tilt the spray guard to the
side.

Remove the waste container.

Empty the waste container and rinse
with water.



Danger

Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 2%. Drive slowly.

Remove vacuum bar, brushes and
spray guard from the device.

If you want to transport the machine on
a vehicle secure it from slipping using
belts/ ropes.

1 Fastening points



Danger

Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull out the battery plug.

Set the drive di-
rection using
the drive direc-
tion button at
the operator
console.

Select speed
range using the
speed button (3
stages).

Observe the
display and wait
till the controls
are initialized.

Set the drive di-
rection using
the drive direc-
tion button at
the operator
console.

Select speed
range using the
speed button (3
stages).

Overload

Cleaning

Press down-
ward the lever
for lowering the
vacuum bar.
The varuum bar
is lowered and
the suction is
activated.

Lower the
cleaning head
by pressing the
button for brush
contact pres-
sure.

Press Cleaning
operations key.
The brush drive
is activated.
The cleaning
head is lowered
(slight brush
contact pres-
sure) and the
detergent liquid
is supplied.
The varuum bar
is lowered and
the suction is
activated.

Adjust the de-
tergent flow us-
ing the water
regulation
knob.

Adjust the de-
tergent flow us-
ing the Dosing
Liquid Deter-
gent switch (4
stages).

Select speed
range using the
speed button (3
stages).

Complete cleaning

Raise the
cleaning head
by pressing the
Brush Contact
Pressure
switch.

Pull the vacuum
bar lowering le-
ver upward; the
vacuum bar is
raised and the
suction is
switched off.

Press Cleaning
operations key.
The brush drive
is switched off
and the clean-
ing head is
raised.
The vacuum
bar is raised af-
ter 15 seconds.
The suction is
switched off af-
ter 30 seconds.

Shutting down

Empty tanks.

Drain off dirt water

Drain off clean water

Emptying waste container

(only BR model)

Transport

Maintenance and care

www.motralec.com / service-commercial@motralec.com / 01.39.97.65.10