background image

9.800-087.0  •  Rev. 10/09

OPERATOR’S MANUAL

  

PRESSURE WASHER 

 

14

PREvENTATIvE MAINTENANCE

This pressure washer was produced with the best available materials and quality craftsmanship. However, you 
as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative 
maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for 
maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform 
maintenance more often under severe conditions.

OIL CHANgE RECORD

Check pump oil and engine oil level before first use of your new pressure washer.

MAINTENANCE SCHEDULE

Engine Oil

Inspect

Every 8 hours or daily

Change

Every 50 hours or monthly

Air Cleaner/Filter

Inspect

Every 8 hours or daily

Change

Every 50 hours or monthly

Fuel Tank Filter

Every 100 hours or yearly

Spark Plug Maintenance

Every 100 hours or yearly

Check Valve Clearance

Yearly

Water Filter

Check

Every 8 hours or daily

Clean

Yearly

Pump Oil

Inspect

Every 25 hours or weekly

Change

Yearly

Date Oil Changed

Month/day/year

Estimated Operating 

Hours Since Last  

Oil Change

Date Oil Changed

Month/day/year

Estimated Operating 

Hours Since Last  

Oil Change

Summary of Contents for CD-232336

















Reviews: