background image

English

Operating Instructions HD 645 / HD 650 (SX) / HD 658 / HD 690 (SX)

22

Troubleshooting

Danger!

Before any repair work is undertaken, 
switch the cleaner off and pull out the 
power plug. Have electrical 
components checked and repaired 
only be authorised Customer Service 
personnel.
For faults which are not identified in 
this chapter, or when in doubt or 
when expressly instructed to do so, 
consult authorised Customer Service 
personnel.

Cleaner does not work

„

Check mains voltage.

„

Check connecting cable for damage.

„

If the motor has overheated, let the 
cleaner cool down. Then switch it on 
again.

„

Consult Customer Service if there is an 
electrical fault.

Cleaner does not come up to 
pressure

„

Set nozzle to “high pressure”.

„

Clean nozzle or replace with new one.

„

Clean strainer at the water connection.

„

Evacuate air from the cleaner.

„

Check water inlet volume (see Technical 
Specifications).

„

Check all supply lines to the pump for 
leaks or obstructions.

„

Seek the help of Customer Service if 
necessary.

Pump is leaky

„

Three drops per minute are allowable 
and can appear on the underside of the 
cleaner. Seek the help of Customer 
Service if leaks are more serious.

Pump makes a knocking 
noise

„

Check all supply lines as well as the 
detergent system for leaks.

„

Evacuate air from the cleaner.

„

Seek the help of Customer Service if 
necessary.

Detergent is not being drawn in

„

Set nozzle to “low pressure”.

„

Check detergent suction hose with filter 
for leaks or obstructions and clean it if 
necessary.

„

Clean/renew non-return valve in 
detergent suction-hose connection.

„

Open detergent metering valve or check 
it for leaks/remove obstruction. Also 
clean venting orifice in the cap.

„

Tip the cleaner backwards over the 
wheels. Empty the detergent reservoir 
and rinse it out.

„

Seek the help of Customer Service if 
necessary.

Spare parts

You will find a list of spare parts at the end 
of these operating instructions.

!

Summary of Contents for HD 645














Reviews: