-
14
Ensure that wounds never come into
contact with lead. Always clean your
hands after working on batteries.
When used normally, and when observing
the instructions, lead-acid batteries do not
pose any risk.
However, keep in mind that lead-acid bat-
teries contain sulphuric acid which can
cause chemical burns and corrosion.
If there is spillage or, if the battery is
leaking, acid is escaping, lay down a
binding agent such as sand. Do not let
it reach the sewer system, soil or a body
of water.
Neutralise the acid with lime/baking
soda and dispose of it according to local
regulations.
Contact a waste management compa-
ny to dispose of faulty batteries.
Rinse thoroughly with lots of clear water
if acid gets into the eye or comes in con-
tact with the skin.
Then consult a doctor immediately.
Wash off the acid If it comes in contact
with the clothes.
Change clothing.
Note
: Upon delivery of the appliance the
battery terminal is disconnected, connect
the battery terminal prior to initial commis-
sioning.
Open the engine hood.
Unscrew and remove the angle bracket
of the battery.
Insert battery in battery mount.
Attach the battery by means of an angle
bracket.
Connect pole terminal (red cable) to
positive pole (+).
Connect pole terminal to negative pole
(-).
Attach the pole covers.
Note:
Check that the battery pole and pole
terminals are adequately protected with
pole grease.
ATTENTION
Comply with safety regulations on the han-
dling of batteries. Observe the directions
provided by the manufacturer of the charg-
er.
ATTENTION
Charge the battery only with an appropriate
charger.
Open the engine hood.
Disconnect battery.
Connect positive terminal cable from
the charger to the positive pole connec-
tion on the battery.
Connect negative terminal cable from
the charger to the negative pole con-
nection on the battery.
Plug in mains connector and switch on
charger.
Note:
When the battery is charged, first re-
move the charger from the mains and then
disconnect it from the battery.
Open the engine hood.
Disconnect pole terminal to negative
pole (-).
Disconnect pole terminal to positive
pole (+).
Remove the battery from the battery
holder.
Dispose of the used battery according
to the local provisions.
몇
CAUTION
Risk of damage!
Do not clean the appliance with a water
hose or high-pressure water jet (danger
of short circuits or other damage).
Do not use aggressive and abrasive de-
tergents.
DANGER
Health hazard!
Wear dust mask and protective gog-
gles.
Open the engine hood.
Blow through machine with com-
pressed air.
Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Close engine bonnet.
Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Observe the inspection checklist!
The service hour counter indicates the time
of the maintenance intervals.
Read the service hours: Push the direc-
tion keys "upwards" or "downwards".
Note
: If the value reaches "0", a service
message with the phone number of the
local service branch is displayed when
the appliance is switched on.
Note:
Where maintenance is carried out by
the customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialised Kärch-
er dealer may be contacted at any time.
Note:
For description, see section on Main-
tenance work.
Daily maintenance:
See chapter "Prior to start/safety test".
Weekly maintenance:
Check leakiness of fuel or gas connec-
tions.
Check dust filter and clean filter box, if
required.
Check air filter.
Check oil level of sweeper hydraulics.
Check hydraulic lines for leaks.
Check moving parts for freedom of
movement.
Check the sealing strips in the sweep-
ing area for position and wear.
Maintenance to be carried out every 100
operating hours:
Change engine oil (initial change after
20 operating hours).
Check and clean spark plug, replace if
necessary.
Clean air filter.
Maintenance to be carried out every 200
operating hours
Replace the air filter insert.
Clean the fuel filter.
Diesel engine: Clean oil filter, replace in
case of damage
Maintenance following wear:
Replace sealing strips.
Replace roller brush.
Replace side brush.
Note:
In order to safeguard warranty
claims, all service and maintenance work
during the warranty period must be carried
out by the authorised Kärcher Customer
Service in accordance with the mainte-
nance booklet.
Maintenance to be carried out after 20 op-
erating hours:
Carry out initial inspection.
Maintenance to be carried out every 100
operating hours
Maintenance to be carried out every 200
operating hours
Maintenance to be carried out every 300
operating hours
DANGER
Risk of injury!
When working on the high emptying
system, completely lift and secure the
waste container.
Perform the safeguarding only from
outside the hazard zone.
Insert safety support into the piston rod
for the lifting cylinder and secure it.
DANGER
Risk of injury!
The engine requires approx. 3-4 sec-
onds to come to a standstill once it has
been switched off. During this time, stay
well clear of the working area.
Risk of burns!
Allow the machine sufficient time to cool
down before carrying out any mainte-
nance and repair work.
ATTENTION
Engine oil, diesel and petrol must not be re-
leased into the environment. Protect the
ground and dispose of used oil in an envi-
ronmentally responsible way.
Procedures in the event of unintentional
release of battery acid
Installing and connecting the battery
Charging battery
Remove the battery
Cleaning
Cleaning the inside of the machine
External cleaning of the appliance
Maintenance intervals
Maintenance by the customer
Maintenance by Customer Service
Maintenance Works
General notes on safety
41
EN
Summary of Contents for KM 105/100 R D
Page 2: ...2 ...
