English
17
3. Allow the device to cool down.
4. Remove the safety key.
5. Remove the battery pack (see Chapter
).
6. Secure the device against slipping and tipping over
when transporting in vehicles.
Storage
Clean the device before storing (see Chapter
1. Remove the safety key.
2. Remove the battery pack (see Chapter
).
3. Unlock the handle locks.
Illustration U
4. Push the telescopic handle in completely.
5. Lock the handle locks.
6. Release the quick-release catches and fold down
the handle.
Illustration V
7. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.
Care and service
몇
WARNING
Sharp blade
Incision injuries
Be careful when tipping or lifting the device.
Keep all parts of your body away from the cutting blade.
Cleaning the device
1. Remove the safety key.
2. Remove the battery pack (see Chapter
).
3. Clean the exterior of the device with a soft, damp
cloth or brush each time after use.
Illustration W
Clean the blade before longer storage periods.
4. Tip the device onto the side.
Illustration X
5. Clean the blade and the underside of the device us-
ing a brush.
Illustration Y
Removing blockages
몇
WARNING
Removing blockages
Incision injuries from the sharp blade or sharp-edged
objects
Wear protective gloves when checking for blockages or
removing blockages.
1. Switch the device off and wait until the blade comes
to a standstill.
2. Remove the safety key.
3. Remove the battery pack (see Chapter
).
4. Remove the grass bag and check for blockages.
Remove any blockages.
5. Check the ejection shaft for blockages. Remove any
blockages.
6. Tip the device onto the side.
7. Check the underside of the device and the blade for
blockages. Be careful when removing blockages be-
cause the blade can move while doing this.
Replacing the blade
1. Remove the safety key.
2. Remove the battery pack (see Chapter
3. Clean the underside of the device (see Chapter
4. Lock the blade and then loosen the screw.
Illustration Z
5. Remove and dispose of the blade.
Illustration AA
6. Fit the new blade into the holder.
Illustration AB
7. Lock the blade and then tighten the screw.
Illustration AC
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
The device switches off
The device overload protection system has triggered.
1. Release the ON/OFF lever.
2. Press the start button and the ON/OFF lever.
The battery pack overheating protection has triggered.
1. Wait until the battery pack temperature lies within
the normal range.
2. Charge the battery pack if the device cannot be
switched on.
The charge status indicator does not show
The battery pack overheating protection has triggered.
Release the ON/OFF lever.
Remove the battery pack.
Technical data
Subject to technical modifications.
LMO
530/36
Device performance data
Nominal voltage
V
36
Cutting width
cm
53
Cutting height
cm
3-11
Grass bag volumes
l
70
Maximum speed
/min
3100 ±
5%
Determined values in acc. with EN 60335-2-77
Sound pressure level L
pA
dB(A)
82,2
Uncertainty K
pA
dB(A)
3,0
Sound power level L
WA
+ K uncer-
tainty
WA
dB(A)
95
Right handle hand-arm vibration
value
m/s
2
0,8
Left handle hand-arm vibration
value
m/s
2
0,8
Uncertainty K
m/s
2
1,5
Dimensions and weights
Length x width x height
mm
1568 x
548 x
1075
Weight (without battery pack)
kg
32,6
Summary of Contents for LM 530/36 Bp
