-
7
For float position:
Press the multi-function lever all the
way forward and lock it in.
The rear left hydraulic connection is ac-
tivated via the lever.
You can use the drive position rotary knob
to select the working and driving position.
몇
Important
The driving direction selector switch must
be set to NEUTRAL/STOP before you can
use the drive position rotary knob!
If the drive pedal is pressed, the motor
speed will increase. The pedal is spring-
loaded; if you remove your foot, the motor
speed will decrease.
몇
Important
During transport drives, use the drive pedal
carefully, because there is a risk of sudden
speed decrease!
The document pouch is located behind
the driver's seat. Always keep the en-
closed documents in this pouch. This
way, you and possible transport com-
panies will always have access to im-
portant information.
Danger
Risk of explosion!
–
Only use the fuels specified in the Op-
erations Manual.
–
Do not refuel the machine in enclosed
spaces.
–
Smoking and naked flames are strictly
prohibited.
–
Ensure that no fuel reaches the hot
open surfaces.
Switch off engine.
Open fuel filler cap.
Fill in diesel.
Insert the fuelling gun as deep as possi-
ble into the fuel nozzle. Do not add any
more fuel once the fuelling gun stops
according to the settings.
Wipe off any spilt fuel and close fuel fill-
er cap.
Estimate the fuel requirement in order
to avoid overflows.
The reservoir for windshield wiper fluid is
located on the rear right side of the ma-
chine.
Check the fluid level daily and refill
commercially sold windshield wiper flu-
id as necessary.
Danger
Danger of accident. Do not adjust the driv-
er's seat while driving.
1 Arm rest incline
2 Lever for seat adjustment
3 Spring hardness
4 Height adjustment
5 Damping
The left arm rest can be folded up to get
in and out.
The right arm rest can be adjusted for
incline, height and position, matching
the control of the multi-function lever.
Danger
Danger of accident. Do not adjust the steer-
ing wheel position while driving.
1 Locking
Pull on the lock.
Set the steering wheel to the desired
position.
Slide the lock back and make sure it
locks in.
Danger
Risk of accidents, injuries. If one point of
the safety check is not fullfilled, the appli-
ance must not be taken into operation, but
must be repaired.
The safety check must be performed be-
fore each use of the appliance.
–
Check the hydraulic oil level.
–
Check engine oil level.
–
Check cooler water level.
Control for rear work hydraulics
Drive position preselector
WORK RANGE 1:
For hydraulic attachment. The
max. speed represents the set mo-
tor speed.
Important
! The speed is then reg-
ulated electronically via the drive
pedal.
WORK RANGE 2:
Working position with load sens-
ing. When the load on the attach-
ment fluctuates, the working speed
is regulated electronically.
SLOW TRANSPORT RANGE:
The drive speed is regulated via
the drive pedal. Max. speed ap-
prox. 20 km/h.
FAST TRANSPORT RANGE:
The drive speed is regulated via
the accelerator pedal. Max. speed
approx. 30 km/h or 40 km/h with
speed level 2.
Drive pedal (foot accelerator)
Before Startup
Prior to initial start-up
Refuelling
Fuelling using a can
Windscreen washer system
Adjusting driver's seat
Set the steering wheel position
Prior to start/safety test
Controls on the right side of the machine
9
EN
Summary of Contents for MIC 45 advanced
Page 1: ...w w w kaer cher com r egi st er and w i n MIC 45 classic MIC 45 advanced 59645440 10 13 ...
Page 2: ...2 ...
Page 18: ......
