72
English
몇
CAUTION
Risk of injury due to inadvertently starting up vehicle.
Before you clean and service the vehicle, or exchange
parts or adjust them to a different function, switch off the
vehicle and remove the ignition key.
몇
CAUTION
Risk of burns from hot surfaces and operating fluids
Allow the vehicle to cool down sufficiently prior to all main-
tenance and repair work.
ATTENTION
Do not let fluids such as engine oil, hydraulic oil, brake flu-
id, diesel or coolants end up in the environment. Dispose
of these fluids in an environmentally friendly manner.
ATTENTION
Repair work may only be carried out by authorised custom-
er service centres or by qualified staff in this area who are
familiar with all relevant safety instructions.
Welding work on the vehicle or vehicle chassis is not al-
lowed.
12.2 Service indicator
The service indicator lights up when the respective main-
tenance needs to be done.
The service indicator flashes on the display:
●
after 50 operating hours when the initial inspection
needs to be performed.
●
Next service after 250 operating hours.
●
Then every 500 operating hours.
Note
The service indicator must be reset by the Customer Ser-
vice.
12.3 Maintenance intervals
Note
In order to preserve warranty claims, all servicing and
maintenance work during the warranty period has to be
performed by an authorised Kärcher Customer Service, in
accordance with the inspection check list.
●
Daily before starting operation, see chapter
.
●
Lubricate all bearings after washing the vehicle.
●
If necessary have the safety checks according to the ap-
plicable local regulations performed by the Customer
Service department.
●
The intervals for inspection and maintenance work to be
performed by the customer are listed in the following ta-
ble.
Additional maintenance work is to be carried out by the
Customer Service department in accordance with the
inspection checklist after 250, 500 (annually), 1000,
1500 or 2000 operating hours. Please inform the Cus-
tomer Service department in time.
12.4 Vehicle maintenance plan (to be carried out by customer)
Pos. Assembly
Activity
Daily
Weekly
every 500
hours
or once-a-year*
1
Cabin dust filter
Check for contamination.
Clean or renew a contaminated dust filter.
X (depend-
ing on envi-
ronmental
conditions)
X
Renew
X (earlier if
needed)
2
Steering Visual
inspection
X
Check the bearings on the steering cylin-
der for play.
X
3
Coolant expansion reservoir Check the coolant level.
X
Check the mixing ratio water / antifreeze.
X
4
V-belt
Check the tension.
X
X
5
Screw connections
Visual inspection; tighten if needed.
X
X
6
Engine air filter
Check for contamination.
Clean or renew contaminated engine air
filter.
X
Renew
X (earlier if
needed)
7
Engine oil
Check the oil level prior to travel com-
mencement.
X
Renew
X
8
Engine oil filter
Renew
X
9
Hydraulic oil tank
Check the hydraulic oil level.
X
X
10
Hydraulic couplings and con-
nections
Check for leaks.
X
X
Summary of Contents for MIC 70
