background image

18

English

Note

: The hopper can only be emptied when the supporting

arms have reached a horizontal position. To avoid the dust

billowing up when the hopper is emptied, the waste hopper

should be lowered as far as possible into the discharge

container.

– Tip the waste hopper

1 + 3  

 + 

When  you  release  the  button  for  tipping  the  waste

hopper, the waste hopper returns to its home position

automatically.

– Raise the waste hopper, drive away from the discharge

container and retract the waste hopper.

1 + 4  

 +

Typical applications

!

Caution while sweeping!

Do not sweep up packing bands, wires or similar items,

otherwise the sweeping mechanism will be damaged.
Do not sweep any burning/glowing objects.

For cleaning even surfaces

– set the lever for the main brush roller to the middle

position 

 (minimum brush wear).

For cleaning uneven surfaces

– set  the  lever  for  the  main  brush  roller  to  the  lower

position 

  (increased brush wear).

– switch on blower fan for dust extraction
– for cleaning right up to the edges – lower the side brush

.

If you are sweeping up fine dust, use the side brush as

little as possible as it will increase the amount of dust

stirred up by the sweeper.
If the side brush encounters an obstacle, it automati-

cally  swivels  back  inside  the  outer  contours  of  the

sweeper. Avoid collisions!

– To protect the filter from getting damp when sweeping

wet surfaces, switch off the dust extraction

 Picking up larger items (sticks, tins, etc.)

!

 Caution!

When the bulk waste flap is open, stones or grit could be

thrown forwards by the main brush. Make sure therefore

that  when  you  open  the  flap  no  persons,  animals  or

property are endangered.

– Open the bulk waste flap 

  by hand.

– Drive over the items to be picked up, at low speed and

with the bulk waste flap open.

Note

:  In order to avoid stirring up dust unnecessarily, the

bulk waste flap should be open for short periods only.

 Overcoming obstacles

Obstacles up to 2 cm in height can be driven over without

any problems. Before you do so, open the bulk waste flap

and raise the main brush.
Obstacles more than 2 cm in height can be only be driven

over with the aid of a suitable ramp.

Summary of Contents for NO FOUND KMR 1250 BAT


















Reviews: