46
RLM 4
GB
■ Only use the appliance under
the following conditions:
■
The appliance is not soiled.
■
The appliance shows no
damage or wear.
■
All controls function proper-
ly.
■
The charging station and
power supply as well as
their electrical supply ca-
bles are undamaged and
function properly.
■ Always replace defective
parts with original spare parts
from the manufacturer.
■ Have the appliance repaired if
it has been damaged.
■ The user of the appliance is
responsible for accidents of
the appliance involving other
persons or their property.
3.4.5 Electrical safety
■ Never operate the appliance
when a lawn sprinkler is oper-
ating on the mowing area at
the same time.
■ Do not spray the appliance
with water.
■ Do not open the appliance.
4
INSTALLATION
4.1
Unpacking the machine
1.
Open the packaging carefully.
2.
Carefully remove all components from the
packaging and check for transport damage.
Note:
If there is any transport damage, im-
mediately notify your Kärcher dealer, techni-
cian or service partner in accordance with the
warranty conditions.
3.
Check the scope of supply, see
chapter 2.1
.
If the appliance is going to be sent on, retain the
original packaging and accompanying docu-
ments. They will also be required for return ship-
ment.
4.2
Planning the mowing areas (01)
Location of the charging station (01/1)
■
Shortest possible distance to the largest
mowing area
■
Level surface
■
Protected against direct sunlight and harsh
weather conditions
■
Connection option for power source
■
Free accessibility for the automatic lawn
mower
Routing the boundary cable (01)
The boundary cable must be laid in a continuous
loop in a clockwise direction.
Corridors between mowing areas (01/h)
A corridor is a narrow section in the grass surface
and can be used to connect two mowing areas.
Main area and secondary area(s) (01)
■
Main area (01/HF): This is the grass surface
on which the charging station is located and
whose entire surface can be mowed auto-
matically by the appliance.
■
Secondary area (01/NF): If a grass surface
cannot be reached by the appliance from the
main area, carry the appliance to the second-
ary area by hand if necessary. Secondary ar-
eas can be processed using manual opera-
tion.
The main area and secondary areas are bounded
by the same continuous boundary cable, howev-
er.
Position of the entry points (01/X0 – 01/X3)
At the specified mowing time, the appliance
moves along the boundary cable to the specified
entry point and begins to mow there.
Summary of Contents for RLM 4
