-
36
F 074
Contact of high pressure pump at washing station 4 stuck
Call customer service.
F 076
Coiling protection contact of high pressure pump washing station 4 has
triggered.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 077
Oil level of high pressure pump at washing station 4 too low
Refill oil, acknowledge the fault.
F 078
Electronics at washing station 4 defective
Call customer service.
F 080
No connection to remote control electronics at washing station 4
Check the connector of the data cable with the elec-
tronics of the remote control.
F 081
Fault at coin acceptor at washing station 4
Call customer service.
F 082
Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
F 177
Current pickup of pump undercarriage wash too high
Reset motor protection switch; call Customer Ser-
vice if the problem recurs.
F 200
No connection between the SB MB control and the electronics of the
WSO
Call customer service.
F 201
Outputs of the control SB MB to the WSO overloaded
F 202
Hardness sensor shows hard water after regeneration
see "Water remains hard after regeneration"
F 204
Failure in the electronics
Call customer service.
F 210
Level sensor BUFFER TANK EMPTY activated
Fill the tank to the level sensor BUFFER TANK
EMPTY (max. switch delay 60 minutes)
F 211
Level sensor BUFFER CONTAINER EMPTY and BUFFER CON-
TAINER FULL switch simultaneously
Check level switch.
F 212
Level sensor RO PUMP ON and BUFFER CONTAINER FULL switch
simultaneously
F 213
Water pressure at the pump RO below 0.3 bar.
Check the flow pressure of the water supply
Check the water filter
F 214
Site-supplied water preparation reports fault
See operating instructions of the site supplied water
preparation
F 220
Water shortage
See "Low water level in the swimmer tank for warm
water"
F 221
Exhaust temperature is too high
See "Exhaust thermostat switched off“
F 222
Current pickup of circulation pump for warm water too high
Reset motor protection switch. If the fault recurs,
call customer service.
F 223
Burner fault
See "Burner failure"
F 224
Safety thermostat of the burner has got triggered
Reset automatic fuse.
F 225
Burner delay active
Wait until the delay time until the burner restart has
elapsed.
F 226
Flow indicator did not open within 5 seconds after the circulation pump
for warm water was turned off.
Call customer service.
F 227
Flow indicator did not close within 3 seconds after the circulation pump
for warm water was turned off.
F 228
Hot water outlet cools off too slowly after the burner is turned off
Check the warm water circuit.
F 229
Fault in warm water temperature sensor
Call customer service.
F 230
Fault in burner outlet temperature sensor
F 231
Fault in warm water temperature sensor
F 232
Fault in burner outlet temperature sensor
F 233
Water temperature with external supply with warm water hotter than
60°C.
Reduce temperature of the water supply
F 240
Failure exterior temperature sensor
Call customer service.
F 241
Failure exterior temperature sensor
F 242
Current pickup of circulation pump for anti frost protection too high
Reset motor protection switch or fuse. If the fault re-
curs, call customer service.
F 243
Current pickup of circulation pump for wash station heater too high
F 244
Warm water temperature too low, washing station heater was turned
off
Check the the continuous water heater and the
warm water circuit
F 245
Current pickup of foam hose heater for dry foam too high
Reset motor protection switch. If the fault recurs,
call customer service.
F 250
Current pickup of pump for special washing programme too high
F 280
No connection to electronics A6
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 281
Outputs of the electronics A6 overloaded
F 282
Current consumption of pump for rim cleaner too high
F 283
Current consumption of pump for rim cleaner too low
F 284
Contactor of pump for rim cleaner is jammed
Call customer service.
Display
Cause
Remedy
38
EN
Summary of Contents for SB MB
