Kärcher SC 4 EasyFix, Instruction Manual

8

English

Installation

Installing accessories

1. Insert and engage the steering roller and non-driven

wheels.

Illustration B

2. Open the cover on the device socket.

Illustration E

3. Connect the steam connector to the device socket

so that the steam connector audibly engages.

Illustration E

4. Push the open end of the accessory onto the steam 

gun so that the unlocking button on the steam gun 
engages.

Illustration J

5. Push the open end of the accessory onto the spot-

light nozzle.

Illustration K

6. Connect the extension tubes with the steam gun.

a Push the 1st Push the first extension tube onto 

the steam gun so that the unlocking button on the 
steam gun engages.
The connection pipe is connected.

b Push the 2nd extension tube onto the 

1st extension tube.
The connection pipes are connected.

Illustration L

7. Push the accessory and / or the floor nozzle onto the 

free end of the extension tube.

Illustration M

The accessory is connected.

Disconnecting accessories

1. Set the selector switch for the steam volume to the 

rear.
The steam lever is locked.

2. Push the cover on the device socket down and dis-

connect the steam connector from the device sock-
et.

3. Push the unlocking button and pull the parts apart.

Illustration Q

Operation

Filling water

The water reservoir can be removed at any time for fill-
ing or be filled directly at the device.

ATTENTION

Damage to the device

Unsuitable water can block the nozzles or damage the 
water level indicator.
Do not fill in pure distilled water. Use a maximum of 50% 
distilled water mixed with tap water.
Do not use condensation from the clothes dryer for fill-
ing.
Do not use collected rain water for filling.
Do not use cleaning agents or other additives (e.g. 
scents) for filling.

Remove the water reservoir for filling

1. Pull the water reservoir vertically upwards.

Illustration C

2. Fill the water tank vertically with tap water or a mix-

ture of tap water and no more than 50% distilled wa-
ter up to the "MAX" mark.

3. Insert the water reservoir and press downwards until 

it locks into place.

Filling the water reservoir directly on the device

1. Fill tap water or a mixture of tap water and no more 

than 50% distilled water from a vessel into the filling 
hole of the water reservoir up to the "MAX" mark.

Illustration D

Switching on the device

Note

If there is no or too little water in the steam boiler, the 
water pump starts to run and pumps water from the wa-
ter reservoir into the steam boiler. The filling process 
can take several minutes.

Note

The device briefly closes the valve every 60 seconds 
causing an audible soft click. Closing prevents the valve 
from clogging. This does not affect the steam output. 

1. Place the device on a firm surface.
2. Insert the mains plug into a socket.

Illustration F

3. Press the ON switch.

The green heating indicator light flashes.

Illustration G

4. Wait until the green heating indicator stays on.

Illustration H

5. Press the steam lever.

Illustration I

Steam leaks out.

Regulating the steam volume

The expelled steam volume is regulated using the se-
lector switch for steam volume. The selector switch has 
3 positions:

19

Unlocking button

20

Selector switch for steam volume (with child lock)

21

Steam hose

22

Steam connector

23

Spotlight nozzle

24

Round brush (small)

25

Power nozzle

26

Round brush (large)

27

Manual nozzle

28

Manual nozzle microfibre cover

29

Extension tubes (2 x)

30

Unlocking button

31

Floor nozzle

32

Hook and loop fastener

33

Microfibre floor cloth (2 x)

34

Carpet glider

35

Descaler

36

** Steam pressure iron

37

Indicator light (orange) - heating 

38

Steam switch (bottom)

39

Steam connector

** optional