background image

TEICH-AIRE MANUAL

9

Most failed equipment can be repaired at substantially lower costs than replacement with new equipment. 

Please ship according to the instructions provided. 

Kasco does estimates on repairs at the request of the customer. The request for an estimate should be 

included in the letter that accompanies the returned unit and must include a daytime phone number and/or 

email address. Estimate options are as follows: 

• 

We will contact the customer with a total estimated cost for repairs after we have evaluated the unit but 

before we perform the work. 

• 

We will repair the unit only if repair costs are under a dollar amount stated by the customer. Example: 

“Please repair if total is under $150.00 before shipping charges.” 

All estimates that are rejected for repair will be destroyed unless otherwise directed by the customer. If 

the customer would like the unit returned, we will restore the unit as closely as possible to the condition in 

which we found it and ship at the customer’s expense (including shipping and handling charges). 

Billing: Kasco accepts Visa and MasterCard credit card payments. Kasco will call for credit card information 

upon completion of the estimate at the customer’s request. All other warranty and repair inquiries should 

be directed to Kasco at 715-262-4488 or repairs@kascomarine.com 

OTHER REPAIRS

715.262.4488

Kasco Marine
800 Deere Road
Prescott, WI 54021

kascomarine.com  |  sales@kascomarine.com

CONTACT US

Back to Contents

Summary of Contents for KM-120












Reviews: