background image

TEICH-AIRE MANUAL

2

Thank you for purchasing this Teich-Aire rocking piston oil-less compressor. It is manufactured to the 

highest standards using quality materials. Please follow all recommended maintenance, operational, and 

safety instructions, and you will receive years of trouble-free service.

IMPORTANT: PLEASE READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE.

Rocking Piston Compressor

Model

Serial No.

Air Flow

cfm

Max pressure

psi

Voltage

V

Hz

Amp

Phase

Single

Kw

RPM

To avoid accidents, use only as described in this manual.

•  Pump only clean, dry air.

•  Operate at 32 °F – 104 °F (0 °C to 40 °C).

•  Protect the unit from dirt and moisture.

• 

Do not pump flammable or explosive gases or use in an environment that contains such gases.

• 

Protect all surrounding items from exhaust air. Exhaust air can become very hot.

•  Corrosive gases and particulate material will damage the unit. Keep free of any water vapor, oil-based 

contaminants, or other liquids.

•  This pump is oil-less and requires no lubrication.

Correct installation is your responsibility. Ensure 

proper installation conditions and installation clear-

ances for sufficient airflow.

•  Install the compressor in a clean, dry location.

•  Ensure the compressor is protected from dirt, 

moisture, and harmful elements of the outdoor 

environment.

•  Ambient air temperature (readings taken 4” away 

from any surface of the compressor) must not 

exceed 104 °F (40 °C).

•  Ensure that adequate ventilation and cooling air 

(flowing across the compressor) is available to 

keep the compressor from overheating, which can 

cause premature damage.

•  Mount the compressor to a stable, rigid operating 

surface. Using the provided shock mounts will 

reduce noise and vibration.

• 

Kasco offers a simple, durable bracket accessory 

that will allow you to easily mount the compressor 

to a wall, floor, or bench. Please contact your Kas

-

co distributor and ask for the compressor mount 

kit appropriate for the voltage of your compres-

sor (Part #771250 for 120V and Part #771260 for 

240V).

PRODUCT OVERVIEW

Important Product Use Information

Installation Requirements

WARNING

Disconnect electrical power at the circuit breaker 

or fuse box before installing this product.

Install this product where it will not come into 

contact with water or other liquids.

Install this product where it will be protected 

from harmful weather.

Electrically ground this product.

Failure to follow these instructions can result in 

fire, electrical shock, or death.

Electrical Shock Hazard

Electrical Shock Hazard

Plumbing

To facilitate future technical 

assistance and/or parts orders, 

please copy the details from the 

compressor nameplate onto this 

page and save for future reference.

Back to Contents

Summary of Contents for KM-120












Reviews: