background image

TEICH-AIRE MANUAL

4

ELECTRICAL

WARNING

Electrical Shock Hazard

Electrical Shock Hazard

This product must be properly grounded.

Do not modify the plug provided. If it will not fit 

the outlet, have the proper outlet installed by a 

qualified electrician.

If repair or replacement of the cord or plug is 

necessary, do not connect the grounding wire to 

either flat blade terminal. The wire with insula

-

tion that is green or green with yellow stripes is 

the grounding wire.

Check the condition of the power supply wiring. 

Do not permanently connect this product to wir-

ing that is not in good condition or is inadequate 

for the requirements of this product.

Failure to follow these instructions can result in 

fire, electrical shock, or death.

Make sure that the power supply voltage agrees with that listed on the product nameplate. All cords with 

plugs must be plugged into an outlet that is properly installed and grounded in accordance with all local 

codes and ordinances. Hardwired installations must be connected to a grounded, metallic, permanent 

wiring system or an equipment grounding terminal or lead on the product.

It is your responsibility to contact a qualified electrician and assure that the electrical installation conforms 

with all national and local codes and ordinances. The metal capacitor located on the side of the compressor 

must be grounded.

Back to Contents

Summary of Contents for KM-120












Reviews: