Kasco LED6S19-150, Owner'S Manual

2

THANKS
We at Kasco Marine, Inc. would like to both thank and 
congratulate you on your purchase of the Submersible 
LED Light Kit.  This kit will illuminate your fountain 
for a beautiful display.  We thank you for choosing 
Kasco for your fountain and aeration needs and want 

you to be completely satisied with your purchase.

Important Safety

Please read and follow these extremely important 
safety and handling instructions for your Kasco equip-
ment.  Following these instructions will help ensure 
your safety and the quality performance of your equip-
ment.

•  Under NO circumstances should anyone enter 

the water with the electrical equipment plugged 
in and/or in operation.  All Kasco equipment is 
designed and built for use in water, and control 
panels are available with GFCI protection.  How-
ever, it is NEVER recommended to enter the water 
with the equipment in operation.

•  Kasco’s Submersible Light Kits are intended for 

use with a Listed control panel having a GFCI 

protected receptacle, or ield wiring terminals and 

disconnect switch, or a timer with a disconnect for 
use with a GFCI receptacle.  They are intended 

to be mounted on a loating fountain or aerator 

for use in a natural or man-made body of water to 
comply with NEC Article 682.

•  Kasco’s Submersible Light Kits have not been 

evaluated for use in swimming pools, spas or sta-
tionary fountains.

•  The power connection for the light kit is 120Vac 

and MUST be plugged into a GFCI protected 

receptacle or GFCI protected ield terminal con

-

nections.

•  Caution should be used when dealing with any 

electrical and/or moving equipment.

•  NEVER run the unit out of water.  It could create a 

dangerous situation for the operator.

•  Extreme caution should be used around water, es-

pecially cold water, as in Spring, Fall, and Winter, 
which poses a hazard itself.

•  NEVER lift or drag the fountain or light kit by the 

power cords.  If you need to pull the unit to the 
side of the pond, use the anchoring ropes.

•  Do not use waders in ponds/lakes that are deep, 

with drop-offs, drastic slopes, or soft bottom mate-
rial.

•  Do not use a canoe or boat that tips easily during 

installation 

•  To reduce the risk of electrical shock, be certain 

the light kit is connected to the GFCI protected 
lighting circuit of your control panel.  For more 
information regarding your control panel instruc-
tions, refer to your fountain owner’s manual or 
download control panel wiring diagrams from 
http://kascomarine.com/instructions.html. A con-
trol panel must be installed a minimum of 5 feet 
(3m in Canada) from the body of water unless 
separated from the body of water by a fence, wall, 
or other permanent barrier that will make the unit 
inaccessible to persons in the water.

General Instructions

INSPECT THE SHIPMENT
Immediately inspect this shipment for any visible 
damages.  Also cross reference the “Parts Included” 
section to check for part shortages.  Shortages should 
be reported immediately to your Kasco Marine distrib-
utor or representative and damages reported to your 
carrier and Kasco Marine.

Parts Included

LED3S19
•  Submersible 3-Light LED Kit (1)
•  Mounting Brackets (3)
•  ¼” Stainless Steel Lock Washer (9)
•  ¼” Stainless Steel Flat Washer (3)
•  ¼” Stainless Steel Nut (3)
•  ¼” x ½” Stainless Steel Bolt (6)
•  ¼” x 1” Stainless Steel Bolt (3)
•  ¼” x 1-3/8” Stainless Steel Bolt (3)
•  Nylon Cable Ties (6)

TOOLS & SUPPLIES NEEDED
•  Two 7/16” wrenches (or one wrench & a 7/16” 

socket with driver)

•  Wire Cutter (for trimming cable ties)

LED6S19
•  Submersible 6-Light LED Kit (1)
•  Mounting Brackets (6)
•  ¼” Stainless Steel Lock Washer (18)