2-Port Antenna
Frequency Range
Dual Polarization
Half-power Beam Width
Integrated replaceable Remote Control Unit
Adjustable Electrical Downtilt
R1
R1
2-Port Antenna iRCU 698–894 65° 16dBi 0°–10°T
Type No.
80010735
V01
A) Antenna specifi cations
R1, connector 1– 2
R1, connector 1– 2
698 – 894
Frequency range
MHz
698 – 806
824 – 894
Polarization
°
+45, –45
+45, –45
Gain
dBd
dBi
13.35
15.5
13.85
16
Horizontal Pattern:
Half-power beam width
°
67
65
Front-to-back ratio
dB
Copolar: > 30
Average: 35
Copolar: > 30
Average: 35
Cross polar ratio
Maindirection
0°
Sector
±60°
dB
Typically: > 25
> 11, Avg. 15
Typically: > 25
> 11, Avg. 15
Vertical Pattern:
Half-power beam width
°
11.3
10
Electrical tilt
°
0 – 10, continuously adjustable
Min. sidelobe suppression for
fi rst sidelobe above main beam:
Average:
° T
dB
dB
0 ... 5 ... 10
16 ... 17 ... 17
16 ... 19 ... 20
0 ... 5 ... 10
18 ... 17 ... 16
20 ... 20 ... 20
Impedance
Ω
50
VSWR
< 1.5
Isolation, between ports
dB
> 30
Intermodulation IM3
dBc
< –150 (2 x 43 dBm carrier)
Max. power per input
W
500 (at 50 °C ambient temperature)
698 – 894
X
65°
iRCU
0°–10°
B) iRCU specifi cations (86010149)*
Field replaceable without dismantling the antenna
Logical interface ex factory
1)
3GPP/AISG 2.0
Protocols
Compliant to AISG 1.1 and 3GPP/AISG 2.0
Hardware interface
2)
2 x 8pin connector acc. IEC 60130-9;
according to AISG:
– iRCU in (male): Control / Daisy chain in
– iRCU out (female): Daisy chain out
Power supply
10 ... 30 V
Power consumption
< 1 W (stand by)
< 8.5 W (motor activated)
Adjustment time (full range)
40 sec.
Adjustement cycles
> 50,000
Certifi cation
CE,
3)
* See mounting instructions and warnings.
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG
1.1 and vice versa with a vendor specifi c command. Start-up operation of the iRCU
86010149 is possible in a RET system supporting AISG 1.1 or supporting 3GPP/AISG
2.0 after performing a layer 2 reset before address assignment. The protocol can also
be changed as follows:
AISG 1.1 to 3GPP:
Enter „3GPP“ into the additional data fi led
„Installer’s ID“ and perform a layer 7 reset or a power reset.
3GPP to AISG 1.1:
Enter
„AISG 1“ into the additional data fi eld „Installer’s ID“ and perform a layer 2 reset or a
power reset. After switching the protocol any other information can be entered into the
„Installer’s ID“ fi eld.
2)
The tightning torque for fi xing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The
connector should be tightened by hand only or using the torque screwdriver (85010080)
as described in the connecting cable data sheet (86010007, ...)!
3)
Tested to comply with FCC Standards. This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
698 – 894
–45°
7-16
698 – 894
+45°
7-16
iRCU
in
out
8pin
male
8pin
female
80010735
V01
Page 1 of 2
936.4273/
b
.1
Subject to alteration.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Downloaded from
