background image

936.4054/b

.1

     Subject to alteration.

86010149

   Page 1 of 2

Integrable Remote Control Unit (iRCU)

Type No.

86010149

Protocols

Compliant to AISG 1.1 and 3GPP/AISG 2.0

Logical interface ex factory 

1)

AISG 2.0/3GPP

Input voltage range

10 ... 30 V (pin 1, pin 6)

Power consumption

< 1 W (stand by); < 10 W (motor activated)

Connectors 

2)

2 x 8 pin connector according to IEC 60130-9; according to AISG

Daisy chain in: male; Daisy chain out: female

Hardware interfaces

RS 485A/B (pin 5, pin 3);

power supply (pin 1, pin 6); DC return (pin 7);

according to AISG / 3GPP

Adjustment time (full range)

40 sec (typically, depending on antenna type)

Adjustment cycles

> 50,000

Temperature range

–40 °C … +60 °C

Protection class

IP 24

Lightning protection

AISG interface (each pin);

2.5 kA (10/350µs); 8 kA (8/20µs)

Weight

480 g (1.1 lbs)

Packing size

245 x 93 x 102 mm, (9.6 x 3.6 x 4 inches)

Dimensions (H x W x D)

170 x 68.5 x 66 mm, (6.68 x 2.7 x 2.6 inches)

1)  

The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 and vice versa
with a vendor specifi c command.

Please note:

If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the 
iRCU must be switched to the appropriate standard of the Primary before installation. Please contact 
Kathrein for further information.

2)

 The tightning torque for fi xing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector
should be tightened by hand only!
Standards  

 EN 60950-1 (Safety)
EN 55022 (Emission)
EN 55024 (Immunity)
ETS 300019-1-4 (Environmental)

Certifi cation: 

CE, FCC15.107 class B

Scope of supply:  Integrable Remote Control Unit

Kathrein’s 86010149 integrable Remote Control Unit (iRCU) allow operators to control the 
 electrical tilt of compatible antennas without direct access to the antenna.

Compliant to AISG 1.1 and 3GPP/AISG 2.0

Field replaceable without dismantling the antenna

Daisy Chain feasibility

 Allow control of the antenna either locally through a laptop computer, on site desktop compu-
ter, the optional central control unit; remotely via an ethernet network or over the internet

Daisy chain in
(male)

Daisy chain out
(female)

Retaining Screw Torx 20

Bottom view of RCU

170 (6.68˝)

14.6 (0.57˝)

17.4 (0.68˝)

66 (2.6˝)

49.5 (1.45˝)

59.5 (2.34˝)

68.5 (2.7˝)

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082

Phone: 214.238.8800    Fax: 214.238.8801    Email: info@kathrein.com

All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for 80010735V01








Reviews: