Kathrein MobiSet 2 Digital CAP 600 Installation And Operating Manual Download

Page: 2 / 60

CONTENTS

............................................................................................................................... 2

FOREIGN LANGUAGE INSTALLATION MANUAL/DISPOSAL

...................................................... 3

MOBISET 2 CAP 600 COMPONENTS/SCOPE OF DELIVERY

...................................................... 4

PROPER USE

........................................................................................................................... 5

SAFETY INSTRUCTIONS - IMPORTANT NOTES

......................................................................... 6

INSTALLATION AND CONNECTION

........................................................................................... 9

INSTALLATION OF CABLE GLAND AND MOUNTING PLATE

........................................................... 11

INSTALLATION OF TURNTABLE

.............................................................................................. 14

BRIEF INSTRUCTIONS FOR INSTALLING THE TURNTABLE

......................................................... 17

INSTALLATION OF THE UFS 740SW RECEIVER

......................................................................... 19

LAYING CABLES AND CONNECTING THE TURNTABLE

............................................................... 21

CONNECTING TO THE UFS 740SW

......................................................................................... 21

FUNCTIONAL INSTRUCTIONS FOR CONNECTION TO THE ON-BOARD POWER SUPPLY

.................. 22

CONNECTION EXAMPLE FOR 12 V BATTERY CONNECTION

................................................. 23

RECEPTION RANGE/FOOTPRINT

........................................................................................... 24

DISMANTLING FOR SERVICING

.............................................................................................. 25

DISMANTLING

...................................................................................................................... 25

ADDRESS OF THE SERVICE CENTRE

................................................................................... 25

POLARISATION SETTING

....................................................................................................... 26

POLARISATION SETTING

...................................................................................................... 26

SAFETY NOTES

.................................................................................................................... 27

INSTALLATION PROCESS

..................................................................................................... 28

MANUAL LOWERING TO PARK POSITION

.............................................................................. 30

SAFETY NOTES

.................................................................................................................... 30

MANUAL LOWERING

............................................................................................................. 31

TECHNICAL DATA

.................................................................................................................. 32

SIKAFLEX

291 SAFETY DATA SHEET

................................................................................... 35

SIKAFLEX

291 TECHNICAL DATA SHEET

.............................................................................. 40

CAP 600 OPERATING MANUAL

............................................................................................... 42

IMPORTANT INFORMATION FOR CAP 600 BEFORE SETUP

.................................................... 43

REMOTE CONTROL

.............................................................................................................. 43

FIRST INSTALLATION

............................................................................................................. 44

ALIGNMENT (SATELLITE SEARCH)

........................................................................................ 47

MANUAL CORRECTION

........................................................................................................ 48

CHANNEL (SATELLITE) SELECTION

....................................................................................... 49

CHANNEL SELECTION FROM THE CHANNEL LIST

................................................................ 49

CHANGE OF LOCATION/TIMER PROGRAMMING

.................................................................... 50

RESET/PARKING

.................................................................................................................... 51

RESETTING THE MOTORISED ANTENNA

.............................................................................. 51

PARKING THE TURNTABLE

................................................................................................... 52

SPECIAL MESSAGES FROM THE TURNTABLE

....................................................................... 53

DECLARATION OF CONFORMITY

........................................................................................... 57

FOR YOUR NOTES

................................................................................................................. 58

Summary of Contents for MobiSet 2 Digital CAP 600





























































Search results

Summary of Contents for MobiSet 2 Digital CAP 600

Reviews:

Related manuals for MobiSet 2 Digital CAP 600

Brands by name

Popular brands

Kathrein MobiSet 2 Digital CAP 600, Installation And Operating Manual

Search results

Summary of Contents for MobiSet 2 Digital CAP 600

Reviews:

Related manuals for MobiSet 2 Digital CAP 600

Brands by name

Popular brands