![background image](http://html.mh-extra.com/html/kato/premium-cityrange-cr-200rf/premium-cityrange-cr-200rf_instruction-manual_657900134.webp)
- 107 -
W
ha
t to
do
w
hen
the
m
ac
hine
br
ea
ks
do
w
n
16. What to do when the machine breaks down
16-4 Dealing with breakdowns
(541A-0079-0E)
16-4-1 Flat battery
(541A-0275-4E)
If you have the booster cables, use the battery of another machine as the electrical source to start the engine.
The booster cable connection method is as follows.
(1) Make connections [1], [2], [3] and [4] in order as shown below.
Attach the (+)
connectors first, followed by the
(
−
) connectors.
(2)
After making the above connections, increase the speed of the assisting machine engine slightly.
(3)
Refer to the section "Starting the engine" for details of engine starting.
(4) Once the engine starts, disconnect the booster cables in the reverse order from the connection order above. Have
the battery completely recharged or replaced by a gas station or your authorised KATO dealer as soon as possible.
If you make a mistake in connecting the booster cables, the following problems could result, so
work with care.
・
Serial connection with an assisting machine using 24V
Voltage will exceed 24V, which will burn out the starter motor and could cause a fire.
(541A-0080-2E)
16-4-2 Overheating
(541A-0276-2E)
(1) Overheating while driving
1) Stop the machine in a safe place.
2)
Keep the engine at idling speed and open the engine cover to allow air to blow through.
When you have the engine idling and open the engine cover, take care to avoid burns from the
engine cover which could be very hot. Also take care to keep your fingers clear of the rotating
section on the V-belt, fan belt etc. which could trap them.
(541A-0081-0E)
3) When the indicator on the water temperature gauge starts falling,
turn the starter switch to the "ACC" position to shut off the
engine.
When the engine comes to a full stop, turn the key to the "OFF"
position and remove it from the starter switch.
Summary of Contents for PREMIUM CITYRANGE CR-200RF
