6
EN • Screen installation and operation manual
The KAUBER V UltraSlim
XL
Lift is a top
-
of
-
the
-
line, ultra slim lift for
professional installations, designed for installation on suspended ceilings or for
open installations. The
utilized drive guarantees stability and uniformity. Limiters
ensure safety of use. The lift is driven by a reliable Somfy motor and can be
used with most multimedia projectors
available on the market.
The KAUBER V UltraSlim
XL
Lift is perfectly suitable for professional
installations which require precision and many years of unfailing operation
IMPORTANT SAFETY INSTRUCTIONS
1.
Please read through the user manual carefully before using the product,
and follow all of the procedures in the manual to safety use of the
product.
2.
Keep these operating instructions in a safe place and pass them on to
any future user.
3.
Take special note of all warnings listed in these instructions and on the
unit.
4.
Follow Instructions
-
All operating and use instructions should be
followed.
5.
To avoid the risk of damaging the projection lift, connect devices only by
Kauber.
6.
Do not use the product near water, for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool, etc.
7.
The projector lift
is designed to operate on a power supply indicated on
the nameplate. If you are not sure of the type of power supply to your
installation site consult with your local Kauber representative or district
power company.
8.
Power: Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them.
9.
Lightning: For added protection during a lightning storm, or when leaving this
unit unattended and unused for long periods, unplug the unit from the wall
outlet and disconnect the cable system. This will prevent damage to the unit
from lightning and power line surges.
10.
Overloading: Do not overload wall outlets and extension cords as this can result
in fire or electric shock.
11.
Object and Liquid Entry: Never push objects and of any kind into this projection
lift
through openings as they may touch dangerous voltage points or short
-out
parts that could result in a fire or electric shock. Never spill liquid of any kind on
the projection screen.
12.
Servicing: Do not attempt to service this projection lift
yourself as opening or
removing cover may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
13.
Children: Always use this device (lift) out of reach of children.
INSTALLATION AND OPERATIONAL RULES
1.
The lift
should be installed in rooms with room temperature (15
-
25° C),
away from moisture and sunlight.
2.
The properly mounted lift
should be perfectly level at every scale.
3.
The screen should not be attached to heat sources. Incorrect adjustment
of the lift
may permanently damage the projection surface.
4.
The motor used in projection lift
is equipped with thermal protection that
prevents the engine from overheating. It may cause permanent damage. It is not
recommended to run the lift
multiple times in a short period of time.
5.
Please do not pull out the projector
manually as it can cause permanent damage
to the components of the projection lift.
THE DISPOSAL OF UNUSED OR WASTE PRODUCT
Due to the design of the projection screen, it must be disposed of in accordance with the
environmental standards
. After product operation finish it should be removed
in separate, specially specified point:
-
a municipal waste disposal point with appropriate containers for this type of equipment,
-
waste containers at the sale point
These products will be recycled, which will prevent the release of substances contained in them into the environment, and the components will be reused.
GENERAL PRODUCT
-
RELATED INFORMATION
1.
The lift
can be connected only with one external control at the same time.
2.
One remote control (for ex. RC01 / RC02 / Trigger 12V / Trigger230V / IR Receiver /
RS Receiver, etc.) cannot be connected at once to more than one screen, elevator,
roller
-
blind, etc. Such
a connection can only be made by using the SG
-
2 group
controller.
