KaVo 1.004.7783 Instructions For Use Manual Download

Page: 12 / 17

77.2.4 C

Cleaning: Automated internal cleaning

KaVo recommends thermodisinfectors in accordance with EN ISO 15883

that are operated with alkaline cleaning agents at a pH of max. 10 (e.g.

Miele G 7781 / G 7881 – validation was performed with the ""VARIO-TD"

programme, "neodisher

mediclean" cleaning agent, "neodisher

Z" neu‐

tralisation agent, and "neodisher

mielclear" rinsing agent and extends only

to the compatibility of materials with respect to KaVo products).

▶

For program settings as well as cleansers and disinfectants to be used,

please refer to the Instructions for Use of the thermodisinfector (com‐

plying with max. pH value of 10).

▶

In order to prevent negative effects on the medical device, make sure

that the interior and the exterior of the medical device are dry, and then

lubricate immediately with care agents from the KaVo care system.

Setup methods according to DIN EN ISO 17664

77.3 D

Disinfection

CAUTION

Malfunctioning from using a disinfectant bath or disinfectant containing

chlorine.

Defects in the product.

▶ Only disinfect in a thermodisinfector or manually.

Setup methods according to DIN EN ISO 17664

77.3.1 D

Disinfection: Manual disinfection - external

KaVo recommends the following products based on material compatibility.

The microbiological efficacy must be ensured by the disinfectant manufac‐

turer.

▪ Microcide AF from Schülke&Mayr (liquid or cloths)

▪ FD 322 from Dürr

▪ CaviCide from Metrex

Tools required:

▪ Cloths for wiping down the medical device.

Setup methods according to DIN EN ISO 17664

▶

Spray the disinfectant on a cloth, then thoroughly wipe down the med‐

ical device and leave the disinfectant to soak in according to the in‐

structions from the disinfectant manufacturer.

▶

Follow the instructions for use of the disinfectant.

77.3.2 D

Disinfection: Manual disinfection - internal

The efficacy of manual internal disinfection must be demonstrated by the

manufacturer of the disinfection agent. With KaVo products, use only dis‐

infection agents that have been released by KaVo with respect to the com‐

patibility of materials (e.g. WL-cid / made by ALPRO).

▶

Immediately after internal disinfection, lubricate the KaVo medical de‐

vice immediately with care agents from the KaVo care system.

Setup methods according to DIN EN ISO 17664

Summary of Contents for 1.004.7783


















Search results

Summary of Contents for 1.004.7783

Reviews:

Related manuals for 1.004.7783

Brands by name

Popular brands

KaVo 1.004.7783, Instructions For Use Manual

Search results

Summary of Contents for 1.004.7783

Reviews:

Related manuals for 1.004.7783

Brands by name

Popular brands