Gebze OSB 1000 Sk. No: 1015 41480
Kocaeli, Turkey
T
: + 90 262 677 19 00
F
: + 90 262 677 19 01
E
: SATIS@KAYASAFETY.COM
KAYASAFETY.COM
...............................................................................................................................
...............................................................................................................................
...............................................................................................................................
............................................................
* Cable must be inspected for kinks, broken strands, corrosion, abrasion, or
other signs of wear and damage.
* Energy absorber in line should be use.
6.2 During each use:
During performing the work at height if the equipment is connected with
another system, make sure that all pieces of equipment in the system are
correctly positioned with respect to each other.
7. General Information
7.1 Product Life:
* There is no theoretical lifetime of metallic materials. Products must be
inspected and documented on a regular basis to determine if the product is
safe to use. KAYA is not responsible for the use of the product that doesn’t
have a record of annualperiodic control.
* Vertical Lifeline System is made of galvanized steel and stainless steel.
maintenance program. More detail should look material specification.
* Stainless steel is highly resistant to atmospheric corrosion. Depending
on the area of the use superficial rust spots can be seen on the product (In
a short time of a period industrial sites; iron powders and welding pieces.)
Please refer to the manufacturer or authorized dealer for more information
regarding the corrosion occurring on the material depending on the area
of the useI in all circumstances decision to continue to use the product can
only be made if annual periodic control has been performed and resulted
positive by manufacturer or a competent person authorized by manufacturer.
If the product has one of the deviations below it should be withdrawn from
service immediately and should be destroyed to prevent further usage.
* It has suffered a heavy shock load or has had a load dropped onto it.
* If observed signs of corrosion on the product* if product was recorded
not suitable for use during a control and if you have any doubt about that.
* Changes in standards, legislation and changes related to technical use of
it, and similar cases.
Warning:
RA-50 Energy Absorber is made of polyurethane. The maximum
lifespan of these is five years. After 5 years from the installation, RA-50 on
the system must be replaced with a new one that is to be requested from
the manufacturer.
7.2 Storage:
Product comes with its own special case and user manual where the model
number and applicable standard is written. Product should be stored in its
own bag in a cool, dry place out of direct sunlight and at room temperature.
Do not store in areas where damage from environmental factors such as
heat, light, excessive moisture, oil, chemicals and their vapors, or other
degrading elements may be present.
7.3 Maintenance:
Taking good care of the product after each use extends the life of it. Use
metal cleaners to clean the product. For detailed information please contact
us on info@kayasafety.com
7.4 Changes and repair
Changing a part, repair and addition to any component of the system is
strictly forbidden without written authorization of KAYA. Any repairs on
products can only be done by manufacturer or qualified persons authorized
by the manufacturer. All repair and maintenance work must only be
performed in accordance with manufacturer’s instructions KAYA won’t be
responsible for repairs performed by for unauthorized persons. Manufacturer’s
instructions for repair and maintenance can be obtained from authorized
distributor in the official language of the country in which the item is in
service. Please contact authorized distributor in your country.
7.5 Transportation of product:
The product should be transported in a bag to keep it away from moisture,
chemicals and sharp edges as well as to protect it getting in contact with
another objects.
7.6 Periodical inspection of product:
Product must be inspected at least one time in a year by manufacturer or a
competent person authorized by manufacturer.The maintanence dates can
be seen on the warning plate.During the inspection of product following
information should be recorded;Type of the product, model, contact information
of producer, serial number, date of production, date of purchase, date of
first use, next inspection date, problems, recommendations, name and surname
of inspector. For further information visit www.kayasafety.com
7.7 Guarantee:
This product has 3-year guarantee against all material or
manufacturing defects under proper usage and storage conditions. Guarantee
is no more valid if; product is used wrong, tears, cut, corrosion, unauthorised
repair of changes on the product, damages caused by accidents.
8. Certification:
This product is certified in accordance with 89/686/EEC directive by APAVE
SUDEUROPE SAS CE0082 notified Body after tests according to EN 353-1:2014
norms.
* KAYA has CE0123 notified body number TÜV-SÜD Product Service 89/686/
EEC 11 B Quality System certificate and commit to produce each product
same as tested sample.
TÜV SÜD Product Service GmbHBSC Vertrieb SüdDaimlerstrasse 11D-
85748 Garching - GERMANY
Tel. + 49 89 361965-752 Fax + 49 89 361965-799
Warning:
Read user guide carefully before usage.
Manufacturer:
KAYA YAPI İÇ MİM. TAS. İNŞ. TAAH. SAN. ve TİC. A.Ş.
Adsress :
GOSB. 1000 Sok. No:1015 Çayırova 41480 KOCAELI / TURKEY
T :
+ 90 262 677 19 00
F :
+ 90 262 677 19 01
E :
info@kayasafety.com
W :
www.kayasafety.com
