Care and Cleaning
CAUTION: ALWAYS TURN OFF THE POWER SWITCH AND DISCONNECT
THE POWER CORD FROM THE ELECTRICAL OUTLET BEFORE CLEANING.
Daily Maintenance:
1.
Lift the Water Tank from Base and empty all water from the Reservoir. Remove the Tank Cap
and drain any water from the Water Tank. Wipe it clean with a soft, damp cloth. The Mist
Nozzle should be removed during cleaning to prevent damage.
2.
Do not
immerse the Base in water. Gently wipe the Reservoir with a soft, clean, wet cloth.
Do not
attempt to remove or in any other way modify the Water Sensor.
Use care
when
wiping around the Water Sensor; it is delicate and can be easily damaged. Rinse the Water
Tank with lukewarm water after each use. For storage, wipe dry with a soft, clean cloth. Keep
water away from the Air Outlet.
3.
Do not
use detergent to clean any water-containing parts of the humidifier. Detergents and
the film they leave behind can affect the output of the humidifier.
Do not
use abrasive
cleansers or brushes.
4.
Do not
leave water in the Water Tank or Reservoir when unit is not in use as it may result
in the build up of mineral deposits and bacteria that can inhibit the output efficiency of the
humidifier. Please note that if water remains in the Water Tank for more than a day or two,
bacterial growth is possible.
Weekly Maintenance:
1.
Thoroughly clean humidifier every week using a solution of bleach and water (one teaspoon
of bleach in one gallon of water). Fill tank partially with this solution, let stand twenty (20)
minutes, shaking vigorously every few minutes, drain and rinse with clean water until the
bleach smell is gone.
Do not
use detergents as they will interfere with performance of the
humidifier.
2.
Wipe the Reservoir with a soft cloth dampened in the solution. Rinse area thoroughly before
proceeding.
3.
If mineral deposits are evident around the Nebulizer and Water sensor, clean their surfaces
with a soft, clean cloth and a small amount of undiluted white vinegar. If necessary for
removal of mineral deposits, mix a solution of 50% white vinegar and 50% water and fill
the base with enough solution to cover the Nebulizer.
Do not
use detergents.
Do not
immerse the Base in water. Allow it to soak for an hour. Then use a cotton swab to gently
loosen build up on the Nebulizer. Rinse out the Reservoir and wipe clean.
Do not touch
Nebulizer with bare fingers
as any fingerprints or other residue can affect mist output.
Be careful not to damage the Water Sensor.
4.
All surfaces should be thoroughly cleaned with water prior to reuse. The Tank Cap can be
soaked in a solution of 50% white vinegar and 50% water if necessary to remove deposits.
End of Season Maintenance
1.
Follow above weekly cleaning procedure at the end of the humidification season, or when
the humidifier will not be used for several days, being sure to dry all parts. Allow the Water
Tank to air dry before storing.
Do not
store with water inside.
2.
Leave Tank Cap partially loosened during storage to prevent Tank Cap and Gasket from
sticking together. This will prolong the life of the gasket.
3.
Clean the Tank and Base after long periods of storage.
Troubleshooting Guide
If your Humidifier is not working properly, refer to the following:
Problem
Power Switch is set to “On” and
Power Indicator is off
Little or no mist is produced
Water overflows from Reservoir
Condensation forms around humid-
ifier or windows
White Dust Accumulation
Possible Cause
• Unit not plugged in
• No power at outlet
• No water in tank
• Unit is not level
• Mineral deposits on Nebulizer or
Water Sensor
• Water Tank was washed with
detergent
• Blower not operating
• Water is too cold.
• Blower operating but mist not
exiting through mist nozzle
• Nebulizer not functioning
• Tank may be leaking
• Tank Cap is not tight
• Nebulizer is not working properly
• Mist Intensity is set too high
for room size or preexisting
humidity level.
• Hard water used
Solution
• Plug unit in
• Check circuits, fuses, test outlet.
• Fill Water Tank.
• Place on a level surface.
• Clean Nebulizer and Water
Sensor per instructions.
• Rinse thoroughly with clean
water.
• Ensure water in base is adequate
to immerse Water Sensor.
• Use room temperature water.
• Reservoir overfilled. Empty
Reservoir and replace tank.
• Clean Nebulizer per instructions.
• Check the Tank for leaks and
replace if necessary
• Tighten Tank Cap
• Clean Nebulizer per instructions.
• Decrease mist output to low
(on 2-speed models) or open
door to the room.
• Use distilled water
Note:
Failure to keep this unit clean from mineral deposits normally contained in any water sup-
ply will affect the efficiency of operation of this unit. Customer failure to follow these instructions
may void the warranty.
