background image

11

8.  How to flush the unit once a week to 

prevent high water TDS and hardness

•  Empty the ice bin and water reservoir following 

instructions in Section 2.

•  Fill the water reservoir with clean potable water 

to MAX WATER FILL.

•  Plug the unit into power.
•  Press and hold Clean button for 3 seconds to 

start Cleaning mode for the flushing process.

•  When the flushing process is complete (the 

Cleaning LED goes off), drain the water 
following instructions in Section 1

6.  If the Making Ice green LED illuminates but 

the unit has dispensed all ice

•  First, press and hold Make Nuggets button for 

3 seconds to exit the Ice Making mode. 

•  Press and hold Clean button for 3 seconds to 

start the Cleaning mode to melt the clumped 
ice that blocks the infrared beam.

•  Press and hold Clean button again for 3 

seconds in 1 minute to stop.

•  Then press Make Nuggets button once to start 

making ice.

7.  If ice is stuck or jammed and the unit can’t 

dispense ice

•  Remove the stuck ice in the dispense point 

with a spoon.

•  Or break the jammed ice by pressing 

Clean button while you hold Dispense 
Nuggets button.

•  Then press and hold Dispense Nuggets button 

to dispense ice.

Summary of Contents for FDFM1JA01

















Reviews: