background image

 

Thrulink Operations Manual 

 

TROUBLE-SHOOTING 

 

Problem 

Suggestion 

Cannot access web 
GUI 

- Verify correct static IP settings for your computer.  
- Verify secure web browser address is used 
(

https://192.168.1.10

 for example) 

- Attempt to ping the device and check for network connectivity. 
- If ping replies, reboot/power cycle the ThruLink 
- Connect to WAN port and ping WAN IP. If ping replies, access 
the GUI using the WAN IP using the https protocol. If LAN and 
WAN configurations are set to the same subnet, change to 
differing subnets. 
- If still unresponsive, escalate for support 

 
Problem 

Suggestion 

Cannot log in to 
web GUI using 
ID/Password 

- Verify correct ID and password 
- If system has been defaulted, access using default “admin / 
admin” 
- Connect to serial console, choose option 2 to reset interface 
password “admin” 

 
Problem 

Suggestion 

Unsure the network 
is working correctly 

- Use the network tool to ping the gateway IP 
- Use the ping tool to verify other devices on the network 
respond 
- If no response, verify ISP/WAN/LAN configurations 
- Check Tunnel Mode activity messages from System page (see 
page 13 of this manual for details). 
- Power cycle router 

 
Problem 

Suggestion 

Tunnel will not 
connect 

- Check Tunnel Mode activity messages from System page (see 
page 13 of this manual for details).  
- Ping remote Server/Client WAN IP using Network ping tool 
- Ping remote Server/Client WAN IP using MS Command Prompt 
- If applicable, ping gateway IP using local ThruLink Network ping 
tool 
- If applicable, ping gateway IP using MS Command Prompt 
- Verify Firewall settings. If firewall enabled, verify ICMP port has 
been allowed. Disable firewall to check if connection can be 
established. If the MS firewall is disabled, verify no other firewall 
software is enabled. 
- Verify router ports are correctly forwarded 

 

Further assistance is available by contacting the nearest KBC technical support 

representative. See preface page “ii” for contact information and availability. 

 
 
 
 
 
25 

 

Thrulink Operations Manual 

 

WARRANTY INFORMATION 

 
KBC extends the following LIMITED WARRANTY to the original owner/purchaser of this 
product as follows: 

-

 

Two years from the date of initial sale for all wireless and network products. 

-

 

Five years from the date of initial sale for all fiber products. 

1)

 

If, within the specified warranty period, this product, or any part or portion thereof, 
shall prove upon examination by KBC, to be defective in material or workmanship, 
KBC will repair or replace such part or portion at KBC’s option.  The warranty 
period on the repaired or replaced part or portion of this product shall be limited to 
the unexpired term of the original warranty.  The buyer shall be responsible for all 
shipping and transportation of the product to KBC for any performance under this 
warranty. 

2)

 

Conditions and Exceptions: 
a)

 

Any accident to this product, any misuse or abuse, alternation, use in modified 
form, or any attempt to repair this product shall void this warranty.  These 
conditions to the warranty include, but are not limited to, incorrect power 
connections, physical damage due to mechanical shock, exposure to moisture, 
and circuit modification. 

b)

 

SHOULD THIS PRODUCT PROVE DEFECTIVE FOLLOWING PURCHASE, THE 
BUYER, NOT THE MANUFACTURER, DISTRIBUTOR, OR RETAILER, ASSUMES 
THE ENTIRE COST OF ALL SERVICING OR REPAIR, EXCEPT AS OTHERWISE 
PROVIDED BY THE TERMS OF THIS WARRANTY. 

c)

 

FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY ON THIS PRODUCT, 
THE BUYER IS LIMITED TO THE FOLLOWING DAMAGES. (1) THE COST OF 
LABOR TO REPAIR OR REPLACE DEFECTIVE PARTS OR PORTIONS OF THIS 
PRODUCT, AND (2) THE COST OF THE REPAIRED OR REPLACE PARTS OR 
PORTIONS OF THIS PRODUCT. 

d)

 

NO OTHER EXPRESSED OR IMPLIED WARRANTIES HAVE BEEN MADE OR WILL 
BE MADE ON BEHALF OF KBC WITH RESPECT TO THE SALE, REPAIR, 
INSTALLATION, OPERATION, OR REPLACEMENT OF THIS PRODUCT.  KBC 
DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OF THIS 
PRODUCT OR ITS FITNESS FOR ANY PURPOSE, AND THE BUYER AGREES THAT 
THIS PRODUCT IS SOLD “AS IS” AND THAT THE ENTIRE RISK OF QUALITY 
AND PERFORMANCE OF THIS PRODUCT IS WITH THE BUYER, EXCEPT AS 
OTHERWISE PROVIDED BY THE TERMS OF THIS WARRANTY. 

e)

 

Some states/jurisdictions do not allow exclusions or limitations of incidental or 
consequential damages, or limitations on how long an implied warranty lasts, 
so the above exclusions or limitations may not apply to you. 

f)

 

If you do not wish to be bound by any of the provisions in this 

warranty, please return the product(s) immediately. 
3)

 

Contact your dealer regarding return authorizations for out of 

warranty repairs and     any further product information. 

 
 

 

 

 

 

 

 

 

26 

Summary of Contents for ThruLink THLK Series

















Reviews: