background image

14

Operation and Service KBL 6900 / MAX10

Air-conditioning

By pressing the „+“ or „–” keys you can switch the air-
conditioning on or off during the tanning session. Once the air-
conditioning has been switched off, it can only be switched on 
again after an interval of 3 minutes. A small star is displayed to 
confirm this.  
If the request to switch on the system is made earlier, it will be 
registered (big star) and when the interval of 3 minutes is over it 
will be executed automatically. 

Exception

In case that the system has been switched off by means of the 
coin-controlled system, it can be switched on again immediately.

Colour stimulation

The colour of the colour stimulation can be selected by means 
of the „+“ key or by the „ - “ key: Red- Green - Blue. 
You can only switch on one colour, but you can switch them all 
off (see Service level). 
48 high-performance diodes for each colour (Red - Green - 
Blue) produce the mood desired: relaxing blue, stimulating blue 
and calming green. 

This airCon func-
tion is only in 
this level if the 
aquaCool is ac-
tivated.
Otherwise you will 
find airCon one 
level higher as 
the picture shows 
on the right hand 
side.

Main display with air condition (aquaCool is not congurated)

Summary of Contents for 6900 MAX10





























































Reviews:

Related manuals for 6900 MAX10