background image

100.210 - Multi Water Sampler - 12 x 50 ml - Manual 

11

 

Safety Regulations 

 
KC Denmark A/S is not, and cannot be held, responsible for any damage(s) made to equipment or to 
operators who ignore safety precautions or because of misuse or wrong operation.  
 
 

 

 

Disconnect power supply to avoid any unattended operation causing accident to personnel and 
multiple water sampler.

 

 

An expert maintenance technician fully familiar with the attendant hazards must only do all maintenance, 
inspection and repairs.  
 
Persons charged with working on the multiple water sampler and its accessories must be trained specially 
for the purpose with special abilities and experience in this area as well as being equipped with the 
appropriate tools and individual safety equipment. Failure to meet these requirements constitutes a risk 
to personal health and safety and economic damages. 
 
When working on the unit in areas, which are difficult to access or hazardous, ensure to take adequate 
safety precautions for the operator and others in compliance with the provisions of law on health and 
safety at work.  
 
Replace worn component with original spare parts.  

 

 

Rev.: February 1, 2022 - lkj 

 

 
 

 
 

 
 

 
 
 
 

 

KC

 

Denmark A/S

 

Research Equipment 

Limnology 

 Oceanography 

 Hydrobiology 

 

E-mail

sales@kc-denmark.dk

 website

http://www.kc-denmark.dk/

 

Holmbladsvej 17-19, DK 8600 Silkeborg, Denmark. Tel. +45 86 82 83 47 

Bank: Sydbank. SWIFT: SYBKDK22 - IBAN DK5070460000104832  

VAT no. DK 29 61 96 62 

 

Summary of Contents for 100.210












Reviews: