background image

100.210 - Multi Water Sampler - 12 x 50 ml - Manual 

2

 

Multi Water Sampler, 12 x 50 ml 

 

 

 

 

IMPORTANT:  
The system itself is rated for 6000 m depth. The maximum useable depth depends on the 
actual battery cylinder. Model 100.217 (standard delivery) is only for 4000 m depth and for 
6000 m, model 100.226 is required.  

 

KC Denmark A/S is not, and cannot be held, responsible for any damage(s) made to 
equipment or to operators who ignore safety precautions or because of misuse or wrong 
operation.

 

 

 

Item 

Description 

 

 
A complete system requires the following items: 
 

 

100.210

 

 The multi water sampler 

 

60.010

 

 Time lapse trigger incl. tablet and 

preinstalled software  

 

100.217

 

 Battery cylinder (4000 m) with room 

for time lapse trigger (or 100.226 for 6000 m) 

 

100.230

 

 Cable from battery cylinder to motor 

 

100.234 -

  Plug for activating the timer 

 

100.235

 

 Battery charger (not shown on photo) 

 

100.236

 

 Cable for programming   

 

 

 

 

 

 

Loading the sampler 

 

Insert the syringes, one by one, into the slots as 
shown on the photo. 

 

 

 

 

Summary of Contents for 100.210












Reviews: